Epson SureColor F7070 Setup Guide

Epson SureColor F7070 Setup Guide

2 |

Contents

Unpacking the Printer ...........................................................................................................................3 Assembling the Stand .............................................................................................................................6 Installing the Printer ............................................................................................................................10 Installing the Media Feeding Unit .......................................................................................................15 Installing the Take-up Reel System ......................................................................................................19 Setting the Language ............................................................................................................................22 Adjusting the Media System ................................................................................................................23 Loading Media ....................................................................................................................................25 Installing the Software .........................................................................................................................31

USB Installation ............................................................................................................................32 Network Installation .....................................................................................................................33

Unpacking the Printer | 3

Read all of these instructions before using your printer. Also be sure to follow all warnings and instructions marked on the printer and in the Users Guide.

Unpacking the Printer

Before beginning assembly, make sure you have sufficient space to set up and use the printer. The following illustration shows the minimum space required for using the printer:

Callout Distance

1 19.7 in. (500 mm)

2 3.9 in. (100 mm)

3 68.9 in. (1750 mm)

4 39.4 in. (1000 mm)

5 114.3 in. (2903 mm)

6 19.7 in. (500 mm)

7 39.4 in. (1000 mm)

8 142.5 in. (3620 mm)

4 | Unpacking the Printer

When choosing a place for the printer, leave adequate room for easy access and ventilation. Avoid locations subject to direct sunlight, excessive heat, humidity, or dust. Be sure the printer is placed on a flat, stable location that can support 496 lb (225 kg).

Caution: Six people are required to unpack and install the printer.

You need an even larger floor space to assemble the printer and stand, so be sure to prepare a large, clear area before unpacking them. Also make sure you save the box and packaging in case you need to ship the printer later.

The following items should be included with your printer:

Printer and Stand Assembly

Printer

Carry bars

Horizontal struts

Power cord

Software and documentation

Hex wrench

Legs

Waste ink tank bracket

Waste ink tank

Caution label Cable support

Waste ink tube bracket

Unpacking the Printer | 5

Media System Assembly

The items below can be found in the Ink Supply System Cover 1 box.

Media feeding unit

Take-up reel

Reel brackets

Adjustment paper Roll core

Bracket and mounting hardware

6 | Assembling the Stand

Assembling the Stand

Make sure you have the following items before assembling the stand.

1. Slide the large horizontal strut into both of the legs.

2. Use the long end of the hex wrench to tighten the pre-placed screws on each of the legs.

back of stand

Assembling the Stand | 7

3. Attach the smaller horizontal strut by securing two B screws (four total) in the back of the right and left legs.

4. Attach the waste ink tank bracket and secure it with a B screw.

5. Attach one B screw to the other side of the bracket, move the slider into place, then attach another B screw.

8 | Assembling the Stand

6. Temporarily fasten the waste ink tube bracket using one B screw.

7. Remove the four screws, then remove the plastic piece.

8. Loosely fasten the mounting pieces to the bracket using three D screws and six washers.

Assembling the Stand | 9

9. Slide the mounting pieces into the grooves, as shown.

10. Remove the screw, align the bracket, then fasten the screw to the stand.

11. Tighten the screws.

10 | Installing the Printer

12. Replace the plastic piece and then fasten it using the screws from step 7.

Installing the Printer

You need six people to install the printer; four people to carry it and two people to position it on the stand. Use the carry bars to lift and move the printer.

Make sure you have the following items before installing the printer.

1. Lock the casters and fix the stand in place. To fix the stand, rotate the feet clockwise until theyre firmly placed on the ground.

Installing the Printer | 11

2. Insert the carry bars into both sides of the printer with the locking bolts toward the ground. Once the carry bars are inserted, rotate them counterclockwise 180 to lock them into place. This keeps the printer from sliding when lifted.

Caution: Before installing the printer, make sure the stand is fixed in place.

3. Lift the printer as shown.

Caution: The printer is heavy. Use at least four people when lifting the printer.

12 | Installing the Printer

4. Lift the printer onto the stand. Line up the marks on the bottom of the printer with the arrows on the top of the stands legs before setting the printer down.

5. Rotate the carry bars clockwise 180 so the locking bolts face the ground. Remove the carry bars from the printer.

6. Attach the printer to the stand using three A screws and washers.

Installing the Printer | 13

7. Open the front cover and remove the tape.

8. Remove the media holding plates.

9. Feed the long waste ink tube through the hole in the stand and secure it in place.

14 | Installing the Printer

10. Feed the short waste ink tube through the bracket as shown. Then feed the end of the long waste ink tube into the top of the short waste ink tube.

11. Remove the cap and inner seal from the waste ink tank.

Note: Keep the cap and inner seal for the waste ink tank. The tank must be sealed properly for disposal.

12. Install the waste ink tank into the bracket. Make sure the waste ink tube is inserted in the opening.

Installing the Media Feeding Unit | 15

13. Place the caution label for your language over the English label, if necessary.

Installing the Media Feeding Unit

You need the following parts to assemble and attach the media feeding unit:

1. Attach the brackets to the back side of the printer with two C screws on each side as shown.

16 | Installing the Media Feeding Unit

Caution: The media feeding unit is heavy and requires two people to install. To avoid damaging the media feeding unit, lift it by holding the two bars on the bottom as shown.

2. Lower the media feeding unit onto the brackets.

3. Attach the media feeding unit to the stand using three C screws.

Installing the Media Feeding Unit | 17

4. Attach the media feeding unit to the stand using four C screws.

Note: Leave the screws loose until the service engineer finishes adjusting the media system.

5. Run the communication cable through the cable supports.

6. Lift the port cover.

18 | Installing the Media Feeding Unit

7. Plug in the communication cable and thread it through the cable supports.

8. Make sure the communication cable is fully seated in the port and then close the port cover.

Installing the Take-up Reel System | 19

Installing the Take-up Reel System

You need the following parts to assemble and attach the take-up reel system:

1. Attach the brackets to the front of the printer using two C screws on each side as shown.

Caution: Use at least two people to lift the take-up reel. To avoid damaging the take-up reel, lift it by holding the two bars on the bottom as shown.

20 | Installing the Take-up Reel System

2. Lower the take-up reel onto the brackets.

3. Attach the take-up reel using three C screws as shown.

4. Attach the take-up reel to the stand using four C screws.

Note: Leave the screws loose until the service engineer finishes adjusting the media system.

Installing the Take-up Reel System | 21

5. Connect the communication cable that is attached to the take-up reel system by running it through the horizontal struts to the back of the printer. Place the communication cable in the cable supports and plug it in, making sure to tighten the screws on the plug to secure the cable in place.

6. Attach the cable support to the bottom of the printer.

22 | Setting the Language

7. Thread the power cord through the cable supports. Connect the power cord to the printer and use the cable supports to restrain the cord.

8. Contact a service engineer to attach the Epson Genuine Ink Supply System, Ink Supply System Cover 1, and adjust the printer. Do not turn on the printer until the service engineers work is complete.

9. Plug the printer into a properly grounded outlet.

Caution: Use only the type of power source indicated on the printers label.

Setting the Language

1. Turn on the printer, if necessary.

2. Press the Menu button.

3. Press d or u to select Preferences, and press OK.

4. Press d or u to select Language, and press OK.

5. Select your language, and press OK.

6. Press the y button until you return to the main menu.

Adjusting the Media System | 23

Adjusting the Media System

After completing printer assembly and before loading media, mark the loading position on the left end of the media using the procedure below. This ensures that the media will be fed straight and helps reduce printing errors. The operation requires two people to perform any necessary adjustments in tandem from the front and the back of the printer. Make sure the printer is level and on a level surface. This procedure needs to be performed once during product installation.

1. Open the front cover and raise the media loading lever.

2. Position the rolled side of the adjustment paper at the bottom, and insert it into the printer.

24 | Adjusting the Media System

3. Align the bottom of the adjustment paper with the bottom of the lower label on the ejection guide. Align the right side of the adjustment paper with the longest scale marks on both labels. After aligning the adjustment paper, lower the media loading lever.

4. At the back of the printer, pull the adjustment paper straight down, and place it over the label on the front bar of the media feeding unit. Use a pen to mark the left side of the adjustment paper on the label.

Loading Media | 25

5. Raise the media loading lever and remove the adjustment paper.

Loading Media

1. Turn on the printer.

26 | Loading Media

2. Open the front cover and then raise the media loading lever.

3. Loosen the screws on the roll holders and slide the roll holders towards the outside of the printer.

4. Align the left end of the media with the mark you made on the label.

Loading Media | 27

5. Using two or more people, move the media onto the roll holder, adjusting the roll holder as necessary. When the media is securely on the roll holder, tighten the screw.

6. Turn the roll holder handle counterclockwise until it can not be turned further.

28 | Loading Media

7. Pull up the roll holder lever, slide the roll holder into the media roll, and tighten the roll holder screw.

8. Turn the roll holder handle clockwise until part A is hidden. When part A is hidden, do not turn the handle any further.

Loading Media | 29

9. Pull the media into the printer. If the left end of the media is not at the center of the rectangular area as shown in the figure on the right, return to step 4.

10. Lower the media loading lever.

11. Pull the media through the front of the printer and then raise the media loading lever.

30 | Loading Media

12. Pull the media out until the right end is parallel with the scale marks on the two labels. Then lower the media loading lever.

13. Attach the media holding plates while aligning their positions. The media holding plates should be installed so that the sides of the media are visible through the three holes and the white line on the media holding plates are visible through the windows.

Installing the Software | 31

14. Close the front cover.

15. After loading the media, you will be prompted to choose setup and media options. Choose options as necessary.

Installing the Software

Insert the software CD that came with your printer into your computer and follow the on-screen instructions.

You can use USB or Ethernet network connections.

For USB connection, make sure your system has the appropriate port and that you have a standard, shielded cable, 10 feet (3 m) or less.

Note: Do not connect the printer until a software installation screen prompts you to.

To connect to a network hub, or directly to your computers network interface, you need a standard RJ-45 (CAT-5 or higher) network cable.

32 | USB Installation

USB Installation

1. Power off your printer, then connect the USB cable to the printer and your computer.

2. Insert the CD into your computer.

3. Follow the on-screen instructions to complete the installation.

Network Installation | 33

Network Installation

1. Make sure your printer is powered on.

2. Connect the Ethernet cable to the printer and your networking device.

3. Insert the CD into your computer.

34 | Network Installation

4. Follow the on-screen instructions to complete the installation, keeping the following points in mind:

Do not remove the checkmark from EpsonNet Configuration Utility and EPSON drivers and utilitiesin the software list.

If you see a firewall or network message, make sure the publisher is SEIKO EPSON, and then allow the connection.

EPSON and SureColor are registered trademarks, and EPSON Exceed Your Vision is a registered logomark of Seiko Epson Corporati