Epson FX-880 Product Information Guide
en
EPSON FX-880/FX-1180
11/98 EPSON FX-880/FX-1180 - 1
13
User Replaceable Parts
FX-880
FX-1180
Options
Paper Handling Options
High-capacity cut-sheet feeder (C806381 for FX-880, C806401 for FX-1180) Feeds up to 150 sheets of paper or 25 plain bond envelopes into the printer without reloading. You can load single-sheet paper, single-sheet multi-part forms, or envelopes.
Single-bin cut-sheet feeder (C806371 for FX-880, C806391 for FX-1180) Feeds up to 50 sheets of paper into the printer without reloading. You can load only ordinary single sheets in this feeder.
Additional tractor unit (C800201 for FX-880, C800211 for FX-1180) Use the additional tractor in the pull position along with your standard tractor installed in the front or rear push position to improve paper handling and reduce the chance of paper jams. This setup is especially useful with continuous multi-part forms.
Roll paper holder (#8310) Allows you to use your printer with 8.5-inch roll paper like that used with telex machines.
Front sheet guide (C814001 for FX-880, C814011 for FX-1180) Allows you to load single sheets and carbonless single- sheet multi-part forms of up to 6 parts.
User Replaceable Part Parts Price List Name Part Number
Front cover Cover, front 1036539
Knob Knob 1036511
Logo plate Logo plate 1037486
Optional interface cover Upper connector cover 1002045
Paper guide Sheet guide assembly, rear 1036541
Paper guide support frame
Support frame, sheet guide 1036506
Paper tension unit N/A N/A
Paper thickness lever cap Cap cover 1025333
Printer cover Cover assembly, printer 1036540
Ribbon cartridge Ribbon cartridge #8750
Tractor Tractor assembly 1036538
paper guide edge guides
continuous paper support*
printer cover
front cover
control panel
paper release lever
logo plate
paper tension unit ribbon cartridge
paper thickness lever
knob
sprocket**
AC inlet center support**
parallel interface
optional interface cover
tractor
* The paper guide support frame is beneath the continuous paper support.
** The center support and sprockets are parts of the tractor.
User Replaceable Part Parts Price List Name Part Number
Front cover Cover, front 1038524
Knob Knob 1039337
Logo plate Logo plate 1039511
Optional interface cover Upper connector cover 1037223
Paper guide Sheet guide assembly, rear 1038525
Paper guide support frame
Support frame, sheet guide 1039332
Paper tension unit N/A N/A
Paper thickness lever cap Cap cover 1039356
Printer cover Cover assembly, printer 1038533
Ribbon cartridge Ribbon cartridge #8755
Tractor Tractor assembly 1038519
EPSON FX-880/FX-1180
2 - EPSON FX-880/FX-1180 11/98
Front paper guide (C814021 for FX-880, C814031 for FX-1180) Allows you to load single sheets and carbonless single- sheet multi-part forms of up to 6 parts without removing the tractor from the front push position.
Optional Interface Cards
You can install one of the following EPSON interface cards in your printer.
Printer Specifications
Mechanical
Card Type Model Number
Serial interface C823051
32KB intelligent serial interface C823071
Coax interface C823141
Twinax interface C823151
Type B bidirectional parallel C823452
Multi-protocol Ethernet print server C823572
Printing method: 9-pin impact dot matrix
Printing speed: High speed draft: 410 cps at 10 cpi (max. 455 cps at 12 cpi)
Draft: 310 cps at 10 cpi
Near letter quality: 77 cps at 10 cpi
Printing direction:
Bidirectional logic seeking for text and graphics printing. Unidirectional text or graphics printing can be selected using software commands.
Line spacing: 1/6-inch or programmable in 1/216-inch increments
Printable columns:
FX-880: 80 columns (at 10 cpi) FX-1180: 136 columns (at 10 cpi)
Resolution: Maximum 240 144 dpi (near letter quality)
Interfaces: One standard bidirectional, 8-bit, parallel interface with IEEE 1284 nibble mode support and one optional interface slot.
Paper feed methods:
Friction (front, rear)
Push tractor (front, rear)
Pull tractor (front, bottom, rear)
Push and pull tractor (additional tractor is required)
Cut-sheet feeder (optional)
Roll paper holder (optional)
Paper feed speed: Continuous: 5 inches/second
Intermittent: 62 ms/line at 1/6-inch line spacing
Paper capacity: Single-bin cut-sheet feeder holds up to 50 sheets of 22 lb (82 g/m2) paper
Note: The total thickness of the paper stack can be up to 0.20 inch (5 mm).
High-capacity cut-sheet feeder: up to 150 sheets of 22 lb (82 g/m2) paper up to 25 plain or bond envelopes up to 30 airmail envelopes
Note: The total thickness of the paper stack can be up to 0.59 inch (15 mm).
Buffer: 32KB or 0KB (selectable in the default- setting mode or the EPSON Remote! utility)
Built-in fonts: Bitmap fonts:
EPSON Draft 10, 12, 15 cpi EPSON Roman 10, 12, 15 cpi,
proportional EPSON Sans Serif 10, 12, 15 cpi,
proportional
Barcode fonts:
EAN-13, EAN-8, Interleaved 2 of 5, UPC-A, UPC-E, Code 39, Code 128, POSTNET
Character tables: One Italic and 10 graphical character tables. (Nineteen graphical character tables are available in some countries.)
Character sets: 13 international character sets
EPSON FX-880/FX-1180
11/98 EPSON FX-880/FX-1180 - 3
Dimensions and weight:
Electrical
Note: Check the label on the back of the printer for your printers voltage.
Environmental
Paper
Note: Use recycled paper, labels, envelopes, and roll paper only under normal temperature and humidity conditions, as follows:
Temperature 59 to 77 F (15 to 25 C) Humidity 30% to 60% RH
Do not load paper that is curled or has been folded.
Continuous paper (ordinary and multi-part):
Continuous labels (front and bottom entry only):
Note:
Use only labels mounted on continuous backing sheets.
Reliability: Total print 6.5 million lines volume: (except print head)
Print head life: approx. 200 million characters (draft 10 cpi, 14 dots/character)
FX-880 FX-1180
Height (inches) (mm)
6.1 154
6.1 154
Width (inches) (mm)
16.3 415
23.2 590
Depth (inches) (mm)
13.8 350
13.8 350
Weight (approx.) (lb) (kg)
16.8 7.6
21.2 9.6
Ribbon: Black ribbon cartridge (#8750 for FX-880, #8755 for FX-1180)
Ribbon life of approx. 3 million characters (draft 10 cpi, 14 dots/character)
120 V Model 220 to 240 V Model
Input voltage range 103.5 to 132 V 198 to 264 V
Rated frequency range 50 to 60 Hz
Input frequency range 49.5 to 60.5 Hz
Rated current 0.7 A (maximum 1.6 A)
0.4 A (maximum 0.9 A)
Power consumption Approx. 36 W (ISO/IEC 10561 letter pattern)
Temperature
Humidity (without
condensation)
Operation 41 to 95 F (5 to 35 C)
10% to 80% RH
Operation (recycled paper, envelopes, labels, or roll paper)
59 to 77 F (15 to 25 C)
30% to 60% RH
Storage 22 to 140 F (30 to 60 C)
0% to 85% RH
Minimum Maximum
Width (inches) (mm)
4 101.6
FX-880: FX-1180: 10 16 254 406.4
Length (inches) (one page) (mm)
4 101.6
22 558.8
Copies 1 original + 5 copies
Total thickness (inches) (mm)
0.0025 0.065
0.018 0.46
Weight (lb) (ordinary page) (g/m2)
14 52
22 82
Weight (one sheet (lb) of multi-part) (g/m2)
12 40
15 58
Quality Plain paper, recycled paper, and carbonless multi-part forms with spot gluing or paper stapling on both sides
Minimum Maximum
Label size See figure below
Backing sheet (inches) width (mm)
4 101.6
FX-880: FX-1180: 10 16 254 406.4
Backing sheet (inches) length (mm)
4 101.6
22 558.8
Backing sheet (inches) thickness (mm)
0.0028 0.07
0.0035 0.09
Total (inches) thickness (mm)
0.0063 0.16
0.0075 0.19
Label weight (lb) (g/m2)
17 68
Quality Plain paper
2.5 inches (63.5 mm) min.
corner radius = 0.1 inch (2.5 mm) min.
15/16 inch (23.8 mm) min.
EPSON FX-880/FX-1180
4 - EPSON FX-880/FX-1180 11/98
Single sheets:
Single-sheet multi-part forms (for the optional front sheet or front paper guide only):
Envelopes (rear entry only):
Roll paper (rear entry only, and requires optional roll paper holder):
Printable Area
Continuous paper:
A The minimum top and bottom margins (above and below the perforation) are 0.17 inch (4.2 mm).
B The minimum left and right margins are 0.51 inch (13 mm).
For the FX-880, the maximum printable width is 8 inches (203.2 mm). For paper wider than 9 inches (229.2 mm), the side margins increase to match the width of the paper.
For the FX-1180, the maximum printable width is 13.6 inches (345.4 mm). For paper wider than 14.6 inches (371.4 mm), the side margins increase to match the width of the paper.
Front Entry Rear Entry
Minimum Maximum Minimum Maximum
Width 5.8 in. 148 mm
FX-880: FX-1180: 10.1 in. 16.5 in. 257mm 420mm
5.8 in. 148 mm
FX-880: FX-1180: 10.1 in. 16.5 in. 257mm 420mm
Length 7.2 in. 182 mm
14.3 in. 364 mm
3.6 in. 92 mm
14.3 in. 364 mm
Thickness 0.0025 in. 0.065 mm
0.0055 in. 0.14 mm
0.0025 in. 0.065 mm
0.0055 in. 0.14 mm
Weight 14 lb 52 g/m2
24 lb 90 g/m2
14 lb 52 g/m2
24 lb 90 g/m2
Quality Plain paper, bond paper, and recycled paper
Minimum Maximum
Width (inches) (mm)
5.8 148
FX-880: FX-1180: 10.1 16.5 257 420
Length (inches) (mm)
7.2 182
14.3 364
Copies 1 original + 5 copies
Total thickness (inches) (mm)
0.0047 0.12
0.018 0.46
Weight (one sheet (lb) of multi-part) (g/m2)
12 40
15 58
Quality Carbonless multi-part forms with a line of glue at the top or the side of the form
Minimum Maximum
Envelope size (No. 6)
Width (inches) (mm)
6.5 165
Length (inches) (mm)
3.6 92
Envelope size (No. 10)
Width (inches) (mm)
9.5 241
Length (inches) (mm)
4.1 105
Total thickness (inches) (mm)
0.0063 0.16
0.020 0.52
Differences in thickness within the printable area must be less than 0.0098 inch (0.25 mm).
Weight (lb) (g/m2)
12 45
24 90
Quality Bond envelopes, plain envelopes, and airmail envelopes without glue on the flap
Minimum Maximum
Width (inches) (mm)
8.5 216
Length (inches) (mm)
Thickness (inches) (mm)
0.0028 0.07
0.0035 0.09
Weight (lb) (g/m2)
14 52
22 82
Quality Plain paper
A A
B B
printable area
printable area
EPSON FX-880/FX-1180
11/98 EPSON FX-880/FX-1180 - 5
Single sheets:
A The minimum top and bottom margins are 0.17 inch (4.2 mm).
B The minimum left and right margins are 0.12 inch (3 mm).
For the FX-880, the maximum printable width is 8 inches (203.2 mm). For paper wider than 8.2 inches (209.2 mm), the side margins increase to match the width of the paper.
For the FX-1180, the maximum printable width is 13.6 inches (345.4 mm). For paper wider than 13.8 inches (351.4 mm), the side margins increase to match the width of the paper.
Envelopes:
A The minimum top and bottom margins are 0.17 inch (4.2 mm).
B The minimum left and right margins are 0.12 inch (3 mm).
Roll paper:
A The minimum top and bottom margins are 0.17 inch (4.2 mm).
B The minimum left and right margins are 0.12 inch (3 mm). The maximum printable width is 8 inches (203.2 mm) for the FX-880 and 13.6 inches (345.4 mm) for the FX-1180.
Safety Approvals
120 V model:
Safety standards UL1950 CSA C22.2 No. 950
EMI FCC part 15 subpart B class B CSA C108.8 class B
220 to 240 V model:
Safety standards EN 60950 (VDE, NEMKO)
EMI EN 55022 (CISPR pub. 22) class B AS/NZS 3548 class B
Acoustic noise: Approx. 55 dB (A) (ISO 7779 pattern)
Control Panel Buttons and Lights
Font Lights
Indicate which font is selected. See Chapter 5 of the Users Guide for more information.
Tear Off/Bin Button
Feeds continuous paper forward to the tear-off position.
Feeds continuous paper backward from the tear-off position to the top-of-form position.
Selects a cut-sheet feeder bin when the cut-sheet feeder is installed.
Selects a font when the printer is in the font selection mode.
Tear Off/Bin Light
Flashes when continuous paper is in the tear-off position.
On when bin 1 of the optional cut-sheet feeder is selected.
Off when bin 2 of the optional cut-sheet feeder is selected.
B B
A
A
printable area
A
B B
A
printable area
B B
A
A
printable area
EPSON FX-880/FX-1180
6 - EPSON FX-880/FX-1180 11/98
LF/FF Button
Feeds paper line by line.
Ejects a single sheet or advances continuous paper to the next top-of-form position when held down.
Load/Eject Button
Loads a single sheet of paper.
Ejects a single sheet of paper if a sheet is loaded.
Loads continuous paper from the standby position.
Feeds continuous paper backward to the standby position.
Micro Adjust Buttons
Let you adjust the top-of-form and tear-off positions using the down or up arrow buttons.
Pause Button
Stops printing temporarily, and resumes printing when pressed again.
When held down for three seconds, enters the micro adjust mode. When pressed again, exits the micro adjust mode.
Pause Light
On when the printer is paused.
Flashes when the printer is in the micro adjust mode.
Paper Out Light
On when no paper is loaded or paper is not loaded correctly in the selected paper source.
Flashes when paper has not been fully ejected or a paper jam has occurred.
Operate Button
Turns the printer on and off. The printer is off when the top of this button is even with the button protectors.
Error Indicators
Light Status Beep Pattern
n= on short series of beeps (three times) o = off long series of beeps (five times) f = flashing
If a printer error occurs, use the control panel lights to determine the problem and solution.
Pause Paper Out Beep Pattern
n n
No paper is loaded in the selected paper source.
The paper is not loaded correctly.
Load paper in the selected paper source, remove and reload your paper, or select a different paper source with the paper release lever. The Paper Out light goes off. Press the Pause button to turn off the Pause light.
Pause Beep Pattern
n
The paper release lever is set to the wrong position.
Set the paper release lever to the position for the paper source you want to use. If paper from another paper source is currently in the paper path, press the Load/Eject button to eject the paper; then move the paper release lever to the desired position.
Pause Paper Out Beep Pattern
n f
Continuous paper does not feed to the standby position.
Tear off the printed page at the perforation; then press the Load/Eject button. The paper feeds to the standby position.
A single sheet of paper is not fully ejected.
Press the Load/Eject button to eject the sheet.
Paper is jammed in the printer.
Clear the paper jam as described on page 13.
Pause Paper Out
f f
The print head is overheated.
Wait a few minutes; the printer resumes printing automatically once the print head cools.
Font Tear Off/Bin Pause Paper Out
f f f f
An unknown printer error has occurred.
Turn off the printer and leave it off for several minutes; then turn it on again. If the error recurs, contact your dealer.
Note: The printer beeps once if you press a control panel button when the corresponding function is not available.
EPSON FX-880/FX-1180
11/98 EPSON FX-880/FX-1180 - 7
Status Monitor
The EPSON Status Monitor 2 utility program comes with the printer and is for use only with Windows 95. It monitors the status of the printer, indicates when errors occur, and provides troubleshooting tips.
Paper Positions
Top-of-Form Position
The letters ABC above are printed at the top-of-form position.
The top-of-form position is the position where the printer starts printing on a page of single-sheet or continuous paper.
Note: See page 4 for information on the printable area of your paper.
Tear-off Position
Your continuous paper is in the tear-off position when the perforation is aligned with the printers tear-off edge, so you can easily tear off your printed document.
Standby Position
Your continuous paper is in the standby position when it is attached to the tractor but not loaded in the printer.
Available Paper Paths
Printing on Continuous Paper
You can choose from three tractor positions (front push, rear push, and pull) and three paper entry slots (front, rear, and bottom) for continuous paper printing. The tractor is installed in the rear push position when the printer is shipped.
If you often need to tear off sheets of continuous paper (for example, if you print purchase orders or sales slips), it is best to use the front or rear push tractor. This allows you to use the printers tear-off edge to easily tear off printed sheets of continuous paper at the perforation. Also, when continuous paper is loaded on a push tractor, you can load single sheets of paper from the paper guide without removing the continuous paper.
If you often print on thick or heavy continuous paper, such as multi-part forms or continuous paper with labels, use the tractor in the pull position. The pull tractor provides the best paper jam prevention, and allows you to load continuous paper from the front, rear, or bottom of the printer. However, you cannot use the tear-off feature with the pull tractor.
Note: To use a pull tractor, you can install the tractor that comes with the printer in the pull position, or you can purchase the optional additional tractor (C800201 for FX-880, C800211 for FX-1180) and install it in the pull position.
If you use the push tractor with the optional tractor in the pull position, you can create a push/pull tractor combination. This improves continuous paper feeding and is recommended for printing on continuous pre-printed forms, multi-part forms, or labels, and for printing high-quality graphics.
The table below summarizes the paper paths available for printing on continuous paper.
Paper Path Description
Front push tractor Front paper slot
The paper path from the front slot is almost straight, which reduces the chance of paper jams. Use the front slot when you are printing on thick paper such as multi-part forms.
Rear push tractor Rear paper slot
Do not load thick paper, such as multi-part forms with 5 or 6 parts (1 original plus 4 or 5 copies) in the rear slot. The paper path from the rear slot is curved, and thick continuous paper performs best with a straight paper path.
Pull tractor Front paper slot
The paper path from the front slot is almost straight, which reduces the chance of paper jams. Use the front slot when you are printing on thick paper such as multi-part forms or continuous paper with labels.
Pull tractor Bottom paper slot
Because the bottom slot has the straightest paper path, it is ideal for printing on thick paper, such as multi-part forms or continuous paper with labels.
Note: When loading paper in the bottom slot, be sure to use a printer stand with an opening large enough so that the paper can feed through it without obstruction.
EPSON FX-880/FX-1180
8 - EPSON FX-880/FX-1180 11/98
Caution: Do not load continuous paper with labels in the rear slot; the labels may come off the backing sheet inside the printer and cause a jam.
Note: If you leave the standard tractor in the rear push position and install the optional tractor in the front push position, you can load one type of continuous paper onto the front push tractor and another type onto the rear push tractor. You can easily switch between the two paper types using the paper release lever. Before moving the paper release lever, always press the Load/Eject button to feed the paper in the paper path backward to the standby position.
Printing on Single Sheets
You can load ordinary single sheets (not single-sheet multi- part forms) and envelopes one at a time from the top of the printer, using the paper guide that comes with the printer.
You can also load single-sheet paper using an optional cut- sheet feeder, front sheet guide, or front paper guide.
Paper Release Lever Positions
Use the paper release lever to select which paper source you want the printer to load paper from. The table below shows the corresponding paper path(s) for each paper release lever position.
Single-sheet position
For loading single sheets from the top (from the paper guide or an optional cut-sheet feeder) or from the optional sheet or paper guide in the front.
Front push tractor position
For loading continuous paper from the tractor installed in the front push position. Also set the lever to this position when using the pull and front push tractors in combination.
Rear push tractor position
For loading continuous paper from the tractor installed in the rear push position. Also set the lever to this position when using the pull and rear push tractors in combination.
Pull tractor position
For loading continuous paper from the tractor installed on top of the printer in the pull position. When the tractor is in the pull position, you can load paper in the printer from the front, rear, or bottom slot.
Pull tractor Rear paper slot
You can load ordinary continuous paper in the rear slot. However, loading thick paper in the rear slot is not recommended because the paper path from the rear slot is curved and a paper jam may occur.
Rear push tractor and pull tractor Rear paper slot
To use the rear push tractor with the pull tractor, you need to install the optional additional tractor. The rear slot is not recommended for thick paper.
Front push tractor and pull tractor Front paper slot
To use the front push tractor with the pull tractor, you need to install the optional additional tractor.
Paper Path Description
EPSON FX-880/FX-1180
11/98 EPSON FX-880/FX-1180 - 9
Paper Thickness Lever Positions
The paper thickness lever is located under the printer cover.
You need to set the paper thickness lever for the type of paper you are using, as shown in the table below.
Paper Handling
Loading Continuous Paper Onto a Push Tractor
Front push tractor
Load paper printable side up.
Rear push tractor
Load paper printable side down.
1. If you are using the front push tractor, remove the front cover.
If you are using the rear push tractor, remove the paper guide.
2. Open both sprocket covers.
3. Fit the first four holes of the paper over the sprocket pins (as shown above). Then close the sprocket covers.
Note: Make sure the left and right sprockets are positioned properly for your papers width. If they are too far apart or there is any slack in the paper, you need to move the sprockets.
4. If you are using the front push tractor, reattach the front cover.
If you are using the rear push tractor, reattach the paper guide.
5. Make sure the paper release lever is in the correct position.
6. Make sure that the paper guide is lying flat on the printer and the continuous paper support is in the upright position.
Removing the Printed Document from a Push Tractor
1. Make sure the Tear Off/Bin light is flashing. (You may need to press the Tear Off/Bin button.) When the Tear Off/Bin light is flashing, your paper is in the tear-off position.
Paper Type Lever Position
Ordinary paper (single sheets or continuous paper) 0
Carbonless multi-part forms with: 2 parts (original + 1 copy) 3 parts (original + 2 copies) 4 parts (original + 3 copies) 5 parts (original + 4 copies) 6 parts (original + 5 copies)
1 2 3 4 5
Thin paper 1 or 0
Continuous paper with labels 2
Envelopes 2 to 6
-1 0
1 2
3 4
5 6
EPSON FX-880/FX-1180
10 - EPSON FX-880/FX-1180 11/98
2. Tear off the printed document at the perforation using the tear-off edge of the printer cover. (Pull it toward you for a clean cut.)
3. Press the Load/Eject button to feed the continuous paper backward out of the printer and into the standby position.
Caution: Always tear off your printed document before you press the Load/Eject button. Reverse feeding several pages at a time may cause a paper jam.
Removing Continuous Paper With Labels
1. Tear off the fresh supply of continuous labels at the perforation nearest the paper entry slot.
2. Hold down the LF/FF button to eject the remaining labels from the printer.
Caution: Never press the Load/Eject or Tear Off/Bin button when printing on labels. When fed backward, labels can easily come off the backing sheet and cause a jam.
Switching to Printing on Single Sheets
You can easily switch from printing on continuous paper with a push tractor to printing on single sheets without having to remove or reload paper. Follow the steps below.
Note:
If continuous paper with labels is loaded in the printer, remove it before switching to single-sheet printing.
If the tractor is in the pull position, remove any continuous paper from it before switching to single-sheet printing.
1. If any printed pages of continuous paper remain in the printer, press the Tear Off/Bin button to advance them to the tear-off position, and then tear them off.
Caution: Tear off your printed document before you press the Load/Eject button in the next step. Reverse feeding several pages at a time may cause a paper jam.
Never use the knob to eject paper while the printer is on; this may damage the printer or cause it to lose the tear-off or top-of-form position.
2. Press the Load/Eject button to feed the continuous paper backward to the standby position.
3. Lower the continuous paper support on the paper guide until it clicks into place, then move the paper guide to the upright position.
4. Load single sheets in the printer.
5. Set the paper release lever to the single-sheet position.
Switching to Printing on Continuous Paper
To switch from printing on single sheets to printing on continuous paper with the front or rear push tractor, follow the steps below.
Note: To switch from printing with the optional front sheet guide to printing with the front push tractor, you need to remove the front sheet guide.
1. If a single sheet remains in the printer, press the Load/Eject button to eject it.
Caution: Never use the knob to eject paper while the printer is on; this may damage the printer or cause it to lose the tear-off or top-of-form position.
2. Make sure that the tractor is installed in the front or rear push position and that continuous paper is loaded on the tractor.
3. Set the paper release lever to the appropriate position.
tear here
EPSON FX-880/FX-1180
11/98 EPSON FX-880/FX-1180 - 11
Adjusting the Top-of-Form Position
If your printing begins too high or low on the page, you can use the micro adjust feature to adjust the top-of-form position as described below.
Caution: Never use the knob to adjust the top-of-form position; this may damage the printer or cause it to lose the top- of-form position.
Note:
Your top-of-form position setting remains in effect until you change it, even if you turn off the printer.
The top margin setting made in some application software overrides the top-of-form position setting you make with the micro adjust feature. If necessary, adjust the top-of-form position using your software.
1. Make sure the printer is turned on and paper is loaded.
2. If you are using a push tractor, press the Load/Eject button to advance the paper to the current top-of-form position. If necessary, lift up the printer cover so you can see the paper position.
3. Hold down the Pause button for about three seconds. The Pause light starts flashing and the printer enters the micro adjust mode.
4. Press the Load/Eject
U and LF/FF D buttons to move the top-of-form position up or down on the page.
Note:
The printer has a minimum and a maximum top-of-form position. If you try to adjust it beyond these limits, the printer beeps and stops moving the paper.
When the paper reaches the default top-of-form position, the printer also beeps and stops moving the paper briefly. You can use the default setting as a reference point when adjusting the top-of-form position.
5. Press the Pause button to exit micro adjust mode.
Advancing the Paper to the Tear-off Edge
If you use the front or rear push tractor, you can use the tear- off feature to advance your continuous paper to the printers tear-off edge when you finish printing. You can then easily tear off the printed document.
As described below, you can use the tear-off feature in two ways: manually by pressing the printers Tear Off/Bin button, or automatically by turning on the auto tear-off mode. The Tear Off/Bin light flashes when the paper is in the tear-off position.
Caution: Never use the tear-off feature to feed continuous paper with labels backward; they may come off the backing sheet and jam the printer.
Never reverse feed continuous paper loaded on the pull tractor using the Tear Off/Bin button; the paper may come off the pull tractor and jam the printer.
Using the Tear Off/Bin Button
After the printer finishes printing your document, press the Tear Off/Bin button to advance the paper to the tear-off edge.
Note: If the Tear Off/Bin light is flashing, the paper is in the tear-off position. If you press the Tear Off/Bin button, the printer feeds your paper to the next top-of-form position.
Advancing Paper to the Tear-off Position Automatically
To automatically advance your printed documents to the tear- off position, you need to turn on the auto tear-off mode and select the appropriate page length for continuous paper in the default-setting mode. For instructions, see Using the Default-Setting Mode on page 13.
When auto tear-off is on, the printer automatically advances the paper to the tear-off position whenever it receives a full page of data or a form feed command followed by no more data.
Adjusting the Tear-off Position
If your papers perforation is not aligned with the tear-off edge, you can use the micro adjust feature to move the perforation to the tear-off position. Follow the steps below.
Caution: Never use the knob to adjust the tear-off position; this may damage the printer or cause it to lose the tear-off position.
EPSON FX-880/FX-1180
12 - EPSON FX-880/FX-1180 11/98
Note: Your tear-off position setting remains in effect until you change it, even if you turn off the printer.
1. Make sure the Tear Off/Bin light is flashing (the paper is at the current tear-off position). You may need to press the Tear Off/Bin button.
2. Hold down the Pause button for about three seconds. The Pause light begins flashing and the printer enters the micro adjust mode.
3. Press the Load/Eject
U and LF/FF D buttons to feed the paper backward or forward until the paper perforation is aligned with the tear-off edge of the printer cover.
Note: The printer has a minimum and a maximum tear-off position. If you try to adjust the tear-off position beyond these limits, the printer beeps and stops moving the paper.
4. Press the Pause button to turn off micro adjust mode. Then tear off the printed pages.
When you resume printing, the printer automatically feeds the paper back to the top-of-form position and begins printing.
Replacing the Ribbon Cartridge
Warning: You need to move the print head by hand to install or replace the ribbon cartridge. If you just used the printer, the print head may be hot; let it cool before you replace the ribbon cartridge.
Caution: Make sure the printer is off and unplugged from the electrical outlet. Moving the print head while the printer is on may damage the printer.
1. Remove the printer cover.
2. Press up the tabs on the paper tension unit, then lift the front of the unit and pull it up and out of the printer.
3. Make sure that the print head is not hot; then slide the print head to the middle of the printer by hand.
4. Grasp the used ribbon cartridge by its handle and pull it up and out of the printer.
5. Turn the ribbon-tightening knob of the new ribbon cartridge in the direction of the arrow to remove any slack in the ribbon.
tear-off edge
paper tension unit
ribbon cartridge handle print head
EPSON FX-880/FX-1180
11/98 EPSON FX-880/FX-1180 - 13
6. Hold the ribbon cartridge by its handle and push it firmly down into position; then press down both ends of the cartridge to fit the plastic hooks into the slots.
7. Use a pointed object, such as a ball point pen, to guide the ribbon between the print head and ribbon guide while you turn the ribbon-tightening knob to help feed the ribbon into place.
8. Slide the print head from side to side to make sure it moves smoothly.
9. Install the paper tension unit by placing it on the printers mounting pegs and lowering it into place. Press down both ends of the unit until it clicks into place.
10. Replace the printer cover.
Clearing Paper Jams
1. Press the Operate button to turn off the printer.
2. Remove the printer cover.
3. If continuous paper is jammed in the printer, tear off the fresh supply at the perforation nearest the paper entry slot.
4. Turn the knob on the left side of the printer away from you to eject the paper in the printer.
Caution: Always turn off the printer before you use the knob; otherwise the printer may be damaged or the top-of- form or tear-off position may be lost.
5. Remove any remaining pieces of paper. If the paper is stuck where the printer ejects it, gently pull the paper out of the printer.
6. Replace the printer cover and press the Operate button to turn on the printer. Make sure the Paper Out light is not flashing and the Pause light is off.
Using the Default-Setting Mode
The default settings control many printer functions. While you can often set these functions through your software or printer driver, you may sometimes need to change a default setting from the printers control panel using the default- setting mode.
The following tables summarize the default-setting mode settings and options. The factory settings are bold.
EPSON FX-880/FX-1180
14 - EPSON FX-880/FX-1180 11/98
Default-Setting Mode 1
* These settings are available only in IBM 2380/2381 Plus emulation mode (IBM 2380 Plus for FX-880, IBM 2381 Plus for FX-1180).
Default-Setting Mode 2
* The options available for this setting vary depending on the country.
Changing Default Settings
Follow the steps below to enter the default-setting mode and change the printers default settings.
Note:
To print the language selection and default-setting mode instructions, you need three sheets of letter- or A4-size paper or three pages of continuous paper that is at least 11 inches (279 mm) long and 8.3 inches (210 mm) wide.
If you use single sheets, you need to load a new sheet of paper each time the printer ejects a printed sheet from the paper guide.
1. Make sure paper is loaded and the printer is turned off.
Caution: Whenever you turn off the printer, wait at least five seconds before turning it back on; otherwise, you may damage the printer.
2. Using the tables above, determine whether the setting you want to change is in default-setting mode 1 or 2.
3. To change settings in default-setting mode 1, hold down the Tear Off/Bin button while you press the Operate button to turn on the printer. To change settings in default- setting mode 2, hold down the Tear Off/Bin and LF/FF buttons while you press the Operate button to turn on the printer.
The printer enters the default-setting mode you selected and prints the language selection instructions (one page).
4. Press the Load/Eject button until the Paper Out and Pause lights indicate the language you want, as described in the language selection instructions.
5. Press the Tear Off/Bin button to print the default-setting mode instructions (two pages) in the language you selected.
The printed instructions list the settings you can change, describe how to change them, and show you how the control panel lights help you make settings. Use these instructions to change the printers default settings from the control panel.
Note: The arrows in the instructions indicate the printers current settings.
6. To save your settings and turn off the printer, press the Operate button. This also exits the default-setting mode.
Note: You may exit the default-setting mode any time by turning off the printer while it is paused. Any settings you have made remain in effect until you change them again.
Aligning Vertical Lines in Your Printout
If you notice that the vertical lines in your printout are not properly aligned, you can use the printers bidirectional adjustment mode to correct this problem.
During bidirectional adjustment, the printer prints three sheets of alignment patterns, labeled High Speed Draft, Draft, and NLQ (near letter quality). As described below, you select the best alignment pattern from each sheet.
Setting Options
Skip over perforation Off, On
Auto tear-off Off, On
Auto line feed Off, On
Print direction Bi-D, Uni-D
Software ESC/P, IBM 2380 Plus for FX-880, IBM2381 Plus for FX-1180
I/F (interface) mode Auto, Parallel, Optional
Auto I/F (interface) wait time 10 seconds, 30 seconds
0 slash 0, 0/
High speed draft Off, On (10 cpi), On (12 cpi)
Input buffer Off, On
Buzzer Off, On
Auto CR (carriage return)* Off, On
IBM character table* Table 2, Table1
Setting Options
Page length for front tractor
Length in inches: 3, 3.5, 4, 5.5, 6, 7, 8, 8.5, 11, 70/6, 12, 14, 17
Page length for rear tractor Length in inches: 3, 3.5, 4, 5.5, 6, 7, 8, 8.5, 11, 70/6, 12, 14, 17
Character table Standard model: Italic, PC 437, PC 850, PC 860, PC 863, PC 865, PC 861, BRASCII, Abicomp, Roman 8, ISO Latin 1 All other models: Italic, PC 437, PC 850, PC 437 Greek, PC 853, PC 855, PC 852, PC 857, PC 866, PC 869, MAZOWIA, code MJK, ISO 8859-7, Bulgaria, PC 774, Estonia, PC 866 LAT., ISO 8859-2, PC 866 UKR
International character set for Italic table*
Italic U.S.A., Italic France, Italic Germany, Italic U.K., Italic Denmark 1, Italic Sweden, Italic Italy, Italic Spain 1
EPSON FX-880/FX-1180
11/98 EPSON FX-880/FX-1180 - 15
Note: To print the instruction sheet and alignment patterns, you need four single sheets or four pages of continuous paper of at least the following sizes:
If you use single sheets, you need to load a new sheet of paper each time the printer ejects a printed sheet from the paper guide.
Follow these steps to perform the bidirectional adjustment:
1. Make sure paper is loaded and the printer is turned off.
Caution: Whenever you turn off the printer, wait at least five seconds before turning it back on; otherwise you may damage the printer.
2. While holding down the Pause button, press the Operate button to turn on the printer. The printer enters the bidirectional adjustment mode and then prints instructions and the first set of alignment patterns.
3. As described in the instructions, compare the alignment patterns and select the pattern with the best alignment. Then select the pattern with the best alignment for each of the remaining sets of alignment patterns.
4. After you select the best pattern in the final set of alignment patterns and save your selection by pressing the Tear Off/Bin button, press the Operate button to turn off the printer and exit the bidirectional adjustment mode.
Printing a Self Test
Running the printers self test helps you determine whether the printer or the computer is causing the problem:
If the self test results are satisfactory, the printer is working properly and the problem probably results from your printer driver settings, application settings, computer, or interface cable. (Be sure to use a shielded interface cable.)
If the self test does not print properly, there is a problem with the printer.
You can print the self test using either single sheets or continuous paper.
Note: Use paper of at least the following width:
To perform a self test, follow these steps:
1. Make sure paper is loaded and the printer is turned off.
Caution: Whenever you turn off the printer, wait at least five seconds before turning it back on; otherwise you may damage the printer.
2. To run the test using the Draft font, hold down the LF/FF button while you press the Operate button to turn on the printer. To run the test using the printers near letter- quality fonts, hold down the Load/Eject button while you turn on the printer. Either self test can help you determine the source of your printing problem; however, the draft self test prints faster than the near letter-quality test.
After a few seconds, the printer loads the paper automatically, and then begins printing the self test. A series of characters is printed.
Note: To temporarily stop the self test, press the Pause button. To resume the test, press the Pause button again.
3. To end the self test, press the Pause button to stop printing. If a printed page remains in the printer, press the Load/Eject button to eject it. Then turn off the printer.
Caution: Do not turn off the printer while it is printing. Always press the Pause button to stop printing and the Load/ Eject button to eject the printed page before you turn off the printer.
Printing a Hex Dump
You can print a hexadecimal dump to isolate communication problems between the printer and your software program. In hex dump mode, the printer prints all data it receives from the computer as hexadecimal values.
You can print a hex dump using either single sheets or continuous paper.
Note: Use paper that is at least 8.3 inches (210 mm) wide, such as letter- or A4-size paper.
To print a hex dump, follow these steps:
1. Make sure paper is loaded and the printer is turned off.
Caution: Whenever you turn off the printer, wait at least five seconds before turning it back on; otherwise you may damage the printer.
Paper Type FX-880 FX-1180
Continuous paper 9.5 x 11 inches (241 x 279 mm)
14.8 x 11 inches (376 x 279 mm)
Single-sheet paper Letter or A4 A3 landscape
Paper Type FX-880 FX-1180
Continuous paper 9.5 inches (241 mm) 14.8 inches (376 mm)
Single-sheet paper Letter or A4 A3 landscape
EPSON FX-880/FX-1180
16 - EPSON FX-880/FX-1180 11/98
2. To enter hex dump mode, hold down both the LF/FF and Load/Eject buttons while you press the Operate button to turn on the printer.
3. Open a software program and send a print job to the printer. Your printer prints all the codes it receives in hexadecimal format.
If characters are printable, they appear in the right column as ASCII characters. Nonprintable codes, such as control codes, are represented by dots. By comparing the characters printed in the right column with the printout of the hexadecimal codes, you can check the codes the printer is receiving.
4. To turn off hex dump mode, press the Pause button, eject the printed page(s), and then turn off the printer.
Cleaning the Printer
To keep your printer operating at its best, you should clean it thoroughly several times a year. Follow these steps:
1. Remove any paper loaded in the printer, and turn off the printer. Then remove the paper guide. If an optional cut- sheet feeder is installed, remove it.
2. Use a soft brush to carefully