Epson GQ-3500 v2 User's Manual

EPSON

Serial Interface for the

G Q - 3 5 0 0

Printed in Japan m 88.11-5 Y59099101000

Serial Interface

The serial interface is an option for your CQ-3500 printer. These pages tell you how to install and use the serial interface.

The GQ-3500 serial interface is actually two interfaces in one. It can be used as either an RS-232C interface (the factory setting) or an RS-422 interface, depending on the settings of the jumpers on the circuit board.

Setting up the Serial Interface

When you receive your serial interface, it is configured as an RS232C interface, 9600 baud, 8 data bits, no parity, 1 or 2 stop bits, with the printer ready protocol enabled. This configuration will work for many applications

To use this configuration with PC computers, use the following command at the DOS prompt

MODE COM1:9600,N,8,1,P

If you need to change the configuration of the serial interface follow these steps:

1. Refer to your computer and software documentation to see what the requirements are for a serial interface printer.

2. Select the RS-232C or RS-422 interface. The jumpers at Jl and J2 will have to be reconfigured for RS-422. Because RS232C is the factory setting, the jumpers will not have to be reconfigured if you choose this interface. For information on the location of Jl and J2 and on how to reconfigure the jumpers for the specific settings described below, see the Serial Interface Jumpers section.

If you have changed the factory settings and want to reconfigure the lumpers for RS232C operation, set the jumpers at Jl and J2 as follows. At Jl, move REV, RD, and SRI to the left. At J2, all jumpers should be disconnected.

Serial Interface 1 I

3.

4.

5.

6.

For RS422 operation, set the jumpers at Jl and J2 as follows. At Jl, move REV, RD, and SRI to the right. At J2, set all jumpers in the installed position, except for TR+ and TR-.

Jumpers that were not given a especific setting above do not need to be changed to select RS-232C or RS-422 operation (although they may affect how the interface works).

Select a baud rate by setting DIP switches 4-1, 4-2, and 4-3 as indicated in Table 2. (For more information on setting DIP switches, see the Serial Interface DIP Switches section of this chapter.)

Select 7 or 8 data bits by setting DIP switch 4-4 on for 8 bits per character or off for 7 bits per character. Using 8 bits per character is usually best. If you selected 7 data bits, select even, odd, or no parity and set DIP switches 4-5 and 4-6 appropriately.

Select a handshaking protocol. If you are using a commercial software program, look in the manual to see if it requires a particular protocol. If not, try the printer ready protocol. Set DIP switches 5-l through 5-4 appropriately. Note that you can use more than one protocol at the same time. For additional information, see the Communications Protocols section.

Customize the interface if you need more control of the serial interface. Study the functions shown in Table 3 that describe the jumpers. For example, its possible to add DSR, CIS, and DCD control to the interface.

Installing the Interface

Installing the serial interface is easy and doesnt require any tools. Just follow these steps:

1. Make sum that the power to the printer is off.

2 Set the DIP switches on the interface card as described in Appendix C. Use a ballpoint pen or similar object to set the Switches

I 2 Serial Interface

3.

4.

Configure the jumpers on the serial interface card as described above.

Remove the parallel interface from the back of the printer by loosening the two Knobs and pulling its straight out as shown in Figure 1. Store the parallel in the box that the serial interface came in

Figure 1. Removing the interface

5. Slide the serial interface into the slot on the back of the printer until it is flush with the printer case.

6. Tighten two two knobs to secure the interface.

7. Connect the serial cable from your computer to the interface.

Serial Inteface 3

T h e S e r i a l I n t e r f a c e D I P S w i t c h e s

On the right side of the serial interface are two banks of DIP switches, as shown in Figure 2. Group 4 is on the left and 5 is on the right . ) switches control many of the of the interface ,as detailed in Table 1. settings.

You can use a ballpoint pen to change the switch Because DIP switch groups 1 and 2 are the same for both the

serial and parallel, the DIP switch information in Chapter2 and Appendix C applies to both interfaces

Figure2. The serial interface DIP switches

4 Serial Interface

Table 1. Serial interface DIP switches

Serial Interface 5

Setting the data trader rate

The following table shows the DIP switch settings for the various possible data transfer (baud) rates

Table2. Baud rate settings

The Serial Interface Jumpers

The following tables describe the functions of the jumpers on the serialinterface. The main function of these jumpers is to switch between RS-232 C and RS-422 operation, but some of the jumpers allow you to customize the interface.

The jumpers are located on the interface card as shown in Figure 3.

Figure3. The serial interface jumpers

I 6 serial Interface

The jumpers at Jl The jumpers at J1 are two position jumpers. The small plugs can be

moved from the left two wires to the right two wires to change the settings. Table 3 describes the functions of the jumpers at Jl. When delivered from the factory, all jumpers are in the left position.

Table3. Functions of the jumpers at J1

Serial Interface 7

The jumpers at J2 Jumpers at J2 are single position jumpers; they can be either

installed or disconnected. To change the settigs of these jumpers you must put a jumper plug across the two pins. To disconnect a jumper plug, simply move the plug so that it rests on the left pin only, leaving the right pin open. (All plugs are in this position when the interface is delivered from the factory.)

Table. Function so the jumpers

T2 Tl

E L DM DM+ SD+ TR+ TR-

Connects DM+ and DM- through a 120 ohm resistor. Connects RD+ and RD- through a 120 ohm resistor. Connects RD- to pin 9 Connects RD+topin 10 Connects DM- to pin 23 Connects DM+ to pin 24 Connects SD+topin 12 Connects TR+ to pin 25 Connects TR-to pin 13

Communications Protocols

To achieve the maximum printing speed, the computer should send characters to the printer faster than the printer can print them. This ensures that the printer has to stop and wait for more information. But if you continuously send information to the printer faster than it can print, sooner or later the printers buffer will overflow and information will be lost. A communications protocol keeps the computer from sending more information than the printer can handle. *

The GQ-35CN7's serial interface can use three different kinds of communications protocols These are described in detail below.

The ETX/ACK protocol

The ETX/ACK protocol uses a special pair of control codes, ETX (ASCII 3) and ACK (ASCII 6). The system is very simple: whenever the GQ-3500 gets an ETX out of its input buffer it sends an ACK back to the computer. When the computer receives the ACK it knows it is safe to send more information to the printer without fear of overflowing the buffer.

8 Serial Interface

The GQ-3500 has a buffer that will hold up to 102 characters, including the ETX code at the end of the group. The computer can send the first group of characters and then stop until the first ACK is received. From then on,every time an ACK is received, another group of characters can be sent.

DlP switch 5-2 controls ETX/ACK protocol. If DIP switch 5-2 iS Off, the GQ-35OO is ignored the ETX code.

The DCl/DC3 or XON/XOFF protocol

The DC1/DC3 protocol also uses a special pair of control codes, DCl (AscII 17 decimal, also knwon as XON) and DC3 ( ASCII 19) decimal, also known as XOFF) This communications protocol is selected by turning DIP switch 5-1 on.

In this protocol the printer sends a DC3 to the computer to suspend data entry under the following conditions

1. when the input buffer becomes nearly full (within 128 bytes)

2 When the printer goes offline (by pressing the ONLlNE button)

3. When the printer runs out of paper

4. When the printer runs out of toner

5. When an errror is detected.

when the computer receives the DC3 signal it must stop within 128 characters) sending information until the printer sends a DCl signal to say that there is more room in the buffer. The printer sends the DCl signal when the buffer has room for 255 characters

If DIP switch 5-4 is on, the printer will send an additional DC3 after each additional character it receives after it sends the first DC3. This is called the multiple XOFF function.

The printer ready protocol

The printer ready protocol is a hardware protocol because it uses one of the wires in cable connecting the computer and printer to tell the computer where , the printer is ready to accept information. This communications potocol is selected by turning DIP switch 5-3 on.

serial Interface 9

1. When the input buffer becomes nearly full (within 128 bytes)

2 When the pinter goes off line (by pressing the ON LINE button)

3. When the printer runs out of paper

4. When the printer runs out of toner

5. When an error is detected.

when the DTR signal goes low, the computer musts stop sending data within 128 characters The signal goes back high when the buffer has room for 255 Characters.

If an error conditionoccurs (conditions 2-5 above), the DTR signal will only return to high error has been cleared and the ON L I N E b u t t o n -

When DIP switch 53 is off the DIR pin is always high.

When you are using the Rs422 interface, the function of the DTR pin is taken on by TR+ (pin 25) and TR- (pin 13).

RS-23X Pin Assignments

The RS-232C connector pin assignment and a description of the respective interface signals are shown in Table 5.

10 Serial Interface

Table5. Pins and signals

Serial Interface 11

Table 5. Continued

12 Ser