This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference. 2) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment.
FCC STATEMENT
Frequently Asked Questions (FAQ)
The Power LED should be lit when the power system is working normally. If the Power LED is not lit, please check as follows: A1: Make sure the power cord is connected to the switch with power
source properly. A2: Make sure the voltage of the power supply meets the requirements
of the input voltage of the switch. A3: Make sure the power source is ON.
Q1. The Power LED is not lit.
It is recommended that you check the following items: A1: Make sure that the cable connectors are firmly plugged into the
switch and the device. A2: Make sure the connected device is turned on and working well. A3: The cable must be less than 100 meters long (328 feet).
Q2. The Link/Act LED is not lit when a device is connected to the corresponding port.
Specifications
This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.
CE Mark Warning Do not use this product near water, for example, in a wet basement or near a swimming pool. Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning.
SAFETY NOTICES Cautions
Industry Canada Statement CAN ICES-3 (B)/NMB-3(B)
Explanation of the symbols on the product label DC voltage
RECYCLING This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment. User has the choice to give his product to a competent recycling organization or to the retailer when he buys a new electrical or electronic equipment.
Use only power supplies which are provided by manufacturer and in the original packing of this product.
Safety Information
For technical support and other information, please visit http://www.tp-link.com/support, or simply scan the QR code.
EU declaration of conformity TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/30/EU, 2014/35/EU, 2009/125/EC and 2011/65/EU. The original EU declaration of conformity may be found at http://www.tp-link.com/en/ce
BSMI Notice
PCB
""
Pb
Cd
Hg
CrVI
PBB
PBDE
Operating Temperature Storage Temperature Operating Humidity Storage Humidity
0C to 40C (32F to 104F) -40C to 70C (-40F to 158F) 10% to 90%RH non-condensing 5% to 90%RH non-condensing
Environmental and Physical Specifications
IEEE 802.3, IEEE 802.3i, IEEE 802.3u, IEEE 802.3x CSMA/CD 5/8/16/24 10/100Mbps Auto-Negotiation RJ45 Ports 10BASE-T: UTP category 3, 4, 5 cable (100m) EIA/TIA-568 100 STP (100m) 100BASE-TX: UTP category 5, 5e cable (100m) EIA/TIA-568 100 STP (100m) Power, Link/Act LEDs Ethernet: 10Mbps (Half Duplex), 20Mbps (Full Duplex) Fast Ethernet: 100Mbps (Half Duplex), 200Mbps (Full Duplex) Store-and-Forward Automatically learning, automatically ag
en
en