Panasonic AW-UE100WP v2 Operating Instructions
en
Operating Instructions Excerpted Version
Installation Instructions provided
4K Integrated Camera
DVQX2119YA SS0620RA1081 -FJ Printed in Japan
ENGLISH PJ
ENGLISH Excerpted Version
Before installing and using this product, be sure to read Read this first! (pages 4, 25 to 26). This manual contains information excerpted from the Operating Instructions. For more information, please visit the Panasonic website (https://pro-av.panasonic.net/manual/en/index.html), and refer to the Operating Instructions.
ESPAOL Antes de instalar y usar este producto, asegrese de leer Lea esto primero! (pginas 4 y 27). Si desea obtener ms informacin, visite el sitio web de Panasonic (https://pro-av.panasonic.net/manual/en/index. html) y consulte las instrucciones de funcionamiento y las instrucciones de instalacin.
Before operating this product, please read the instructions carefully and save this manual for future use.
Model No. AWUE100WP Model No. AWUE100KP
2
Trademarks and registered trademarks Microsoft, Windows, Windows 10, Microsoft Edge, Internet
Explorer, ActiveX and DirectX are either registered trademarks or trademarks of Microsoft Corporation in the United States and other countries.
Apple, Mac, macOS, iPadOS, iPhone, iPad, and Safari are registered trademarks of Apple Inc., in the United States and other countries.
Android and Chrome browser are trademarks of Google LLC. Intel and Intel Core are trademarks or registered trademarks
of Intel Corporation in the United States and other countries. Adobe and Reader are either registered trademarks or
trademarks of Adobe Systems Incorporated in the United States and/or other countries.
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc. in the United States and other countries.
NDI is a registered trademark of NewTek, Inc. in the United States.
Other names of companies and products contained in these Operating Instructions may be trademarks or registered trademarks of their respective owners.
About copyright and licence It is expressly prohibited to distribute, copy, disassemble, reverse compile, modify, reverse engineer, or export in violation of export laws the software provided with the unit.
Abbreviations The following abbreviations are used in this manual. Windows Internet Explorer 11 32/64bit is abbreviated to
Internet Explorer.
For the purposes of this manual, the model numbers of the units are given as listed in the table below.
Model number of unit Model number given in manual
AW-UE100WP AW-UE100
AW-UE100KP AWRP150G AW-RP150 AWRP60G AW-RP60
AV-HLC100P AV-HLC100 AVUHS500P AV-UHS500
Illustrations and screen displays featured in the manual What is shown in the manuals illustrations and screen displays
may differ from how it is actually appears. Functions which can be used by Windows Internet Explorer 11
only are indicated using the mark. The screenshots are used in accordance with the guidelines of
Microsoft Corporation.
2 3
Contents
Read this first! ....................................................................................... 4 Lea esto primero! .................................................................................. 4 Installation precautions ........................................................................ 5 Before installation ................................................................................. 7
IR ID switch settings ............................................................................ 7 Service switch settings......................................................................... 7
How to install and connect the unit ..................................................... 8 When using the WVQ105A (optional accessory).............................. 13
Removing the camera ......................................................................... 14 Stand-alone installation
(when the mount bracket is going to be used) ............................. 15 Stand-alone installation
(when the mount bracket is not going to be used) ...................... 18 When installing the unit on a desktop ................................................ 18 When mounting the unit on a tripod ................................................... 18
Connections ......................................................................................... 19 Connecting an NDI|HX compatible switcher ...................................... 19 Connections with a controller (AWRP150) ....................................... 20 System example 1 (Serial control) ..................................................... 21 System example 2 (IP control) ........................................................... 22 System example 3 (IP image transmission, PoE++).......................... 23 System example 4 (NDI) .................................................................... 23
Appearance .......................................................................................... 24
Read this first! ..................................................................................... 25 Lea esto primero! ................................................................................ 27 Read this first! .................................................................................... 28
Note on grounding ............................................................................. 28
Before use ............................................................................................ 28 Overview ............................................................................................ 28 Computer requirements ..................................................................... 28 Disclaimer of warranty ....................................................................... 29 Network security ................................................................................ 29
Features................................................................................................ 30 Accessories ......................................................................................... 31 Optional accessories .......................................................................... 31 Operating precautions ........................................................................ 32 Wireless remote control (optional accessory).................................. 34 Parts and their functions .................................................................... 35
Camera unit ....................................................................................... 35 Wireless remote control: AWRM50G (optional accessory)............... 46
Setting the remote control IDs ........................................................... 47 Network settings.................................................................................. 48
Use the Easy IP Setup Software to establish the units settings........ 48 Use the Easy IP Setup Software Version.2 to establish the units
settings .......................................................................................... 48 Setting the initial account ................................................................... 50 Installing the plug-in viewer software ................................................. 50
How to turn the power on and off ...................................................... 51 Turning the power on ......................................................................... 51 Turning the power off ......................................................................... 51
Troubleshooting .................................................................................. 52 Specifications ...................................................................................... 61 Index ..................................................................................................... 62
Installation Instructions
Operating Instructions
Installation Instructions
Read this first!
WARNING: To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation instructions.
WARNING: Installation should only be performed by qualified installation personnel. Improper installation may result in the entire apparatus falling down and causing injury.
CAUTION: This camera intended for use only with the Mount Bracket enclosed with the unit and Panasonic Direct Ceiling Mount Bracket, WVQ105A. Use with other apparatus is capable of resulting in instability causing possible injury.
CAUTION: To reduce the risk of fire or electric shock, install making sure that the mounting screws do not come in contact with electrical wiring within the wall.
indicates safety information.
Lea esto primero!
ADVERTENCIA: Para evitar heridas, este aparato debe estar firmemente instalado al piso/pared de acuerdo con las instrucciones de instalacin.
ADVERTENCIA: La instalacin solamente debe llevarla a cabo personal cualificado. Una instalacin incorrecta podra provocar la cada del dispositivo y causar lesiones.
PRECAUCIN: Esta cmara ha sido diseada para ser utilizada solamente con la mnsula de montaje suministrada con la unidad y con la mnsula de montaje directo en el techo de Panasonic modelo WVQ105A. La utilizacin con otros aparatos puede causar inestabilidad y posibles lesiones.
PRECAUCIN: Para reducir el riesgo de incendio o descarga elctrica, instlelo asegurndose de que los tornillos de montaje no entren en contacto con el cableado elctrico dentro de la pared.
indica informacin de seguridad.
ENGLISH
ESPAOL
4
Installation Instructions
Installation precautions
Panasonic does not accept any responsibility for accident or damage during installation if procedure in this manual is not followed.
To installation personnel Read the Installation Instructions thoroughly and then perform the operation correctly and safely. Also, always read the Read this first! ( page 4) of this manual as they contain important information. After the installation, give the Installation Instructions to the customer to save for future use.
Ensure that the installation work complies with the technical standards governing electrical equipment.
This unit is for indoor use only. It cannot be used outdoors. Avoid installation in a location where the unit will be exposed to direct sunlight for extended periods or near a cooling or heating appliance. Otherwise, deformation, discoloration, malfunctioning and/or problems in operation may result. Operate the unit where it will not be splashed or sprayed by water.
Use the unit with an installation where the unit is suspended from an overhead surface or with a stand-alone installation. Do not use the unit on its side or tilted at an angle.
Be absolutely sure to use the four bracket mounting screws (M4) for
mounting the mount bracket. These are supplied with the unit. Do not use wood screws, nails, etc. In the case of a concrete ceiling, secure the unit using anchor bolts (for M4) or AY plug bolts (for M4). Recommended clamping torque
M4 : 1.47 N m {15 kgf cm} The withdrawal strength of the mounting location for each screw
must be at least 133 N {13.5 kgf}. When mounting the unit on a ceiling made of plasterboard, for
instance, if it is not strong enough to support its weight, either reinforce the ceiling adequately or use the WVQ105A direct ceiling mount bracket, which is sold separately.
When using a mount bracket which is sold separately, read the handling instructions.
Do not hold the camera head while undertaking the installation work. Doing so may cause malfunctioning.
Desktop installation Hanging installation
OK NG OK NG
Concerning the installation location Install the unit in a stable location which will not be susceptible to shaking. If the unit is installed in a location which is susceptible to shaking, this will cause the units images to shake in turn. Install the unit after conferring in detail with your dealer. Install the unit on a ceiling that is strong enough (such as a concrete ceiling). If the unit is to be installed on a ceiling which is not strong enough, reinforce the ceiling sufficiently first.
Through the adoption of the Direct Drive system and Panasonic proprietary technology, we have achieved quietness and high precision in panning and tilting. In order to get the most from the characteristics of the Direct Drive system, install in a stable location that does not shake and that has sufficient stiffness. Shaking of the installation location can be the cause of performance deterioration and malfunctions in the camera.
If the camera is installed in a location with insufficient stiffness, the pan and tilt control characteristics may be adversely affected, leading to unstable operation. In environments such as the following, there may be unusual operation
sounds during pan and tilt, and operational errors may occur. If you are concerned about unstable pan and tilt operations after installation, please contact your dealer.
small diameter B Single point attachment to a movable structure
Do not install or use the unit in the following kinds of locations. On walls (where the unit would be installed sideways) In locations (including places such as under the eaves of a
building) where the unit would be directly exposed to rain or water In locations such as kitchens where there are high concentrations
of steam and grease In outdoor locations or hot places where the temperature will
exceed 40 C (104 F) In cold locations where the temperature will drop below 0 C (32 F) In locations where the humidity will exceed 85% In locations where chemicals are used such as near swimming pools At sea, in coastal areas or in locations where corrosive gases are emitted In locations where radiation, X-rays, or strong radio waves or
magnetic fields are generated In locations where the unit would be subject to a great deal
of vibration such as on board a vehicle or ship (this unit is not designed to be used in vehicles)
In locations where the temperature is subject to sudden changes such as near the air outlet of an air conditioner or near a door which allows the outside air to come in
AW-UE100 main unit
Mounting conditions Applicable mount bracket Mounting onto the ceiling
Mass Model No. Mass Mounting Recommended screws
No. of screws
Minimum withdrawal strength (per screw)
Approx. 2.2 kg (4.84 lb)
(excluding mount bracket)
Cable cover Approx.
0.1 kg (0.22 lb)
Direct mount (supplied
accessory)
Approx. 0.25 kg (0.55 lb)
Hanging/Desktop M4 screws (supplied accessory) 4 133 N {13.5 kgf}
Ensure that the mounting strength can support a weight that is at least five times the total mass of the equipment, including the cameras main unit.
WVQ105A (optional
accessory)
Approx. 0.15 kg (0.33 lb)
For ceiling M4 screws
(supplied with the WVQ105A)
4
4 5
Installation Instructions
What to avoid to ensure that the unit will perform stably over a prolonged period Using the unit for a prolonged period in a location with high
temperature and humidity levels will cause its parts to deteriorate and shorten its service life.
Ensure that a cooling unit or heating unit will not blow any air directly toward the installation location.
Be absolutely sure to use the supplied brackets and screws to install the camera. Do not mount the unit by employing any methods other than those
specified. Do not remodel the mounting bracket or mounting screws provided
with the unit.
Before installation, always disconnect the power plug When installing, always use the supplied components. Do not disassemble or modify the wall mount adaptor.
Tightening up the mounting screws Tighten up the screws and bolts securely to the degree that is
appropriate for each of the materials used in the mounting location and structures.
After tightening up the screws and bolts, check that there is no unsteadiness and that the parts have been tightened securely.
Use the specified tools and tighten the screws firmly. Tighten up the screws using the specified torque driver. Do not
use electrical drivers or impact drivers.
When the unit is no longer going to be used, do not leave it lying around, but be absolutely sure to dispose of it properly. For details on how to remove the unit, refer to Removing the camera ( page 14).
When installing, transferring or disposing of the unit, be absolutely sure to hold it by its pedestal area. Problems may result if the camera head is held or rotated.
Do not attach a filter, hood, extender or other parts to the unit.
Use the dedicated AC adaptor and power cable provided with the unit. Connect the AC adaptor and power cable to the power inlet securely.
Installing the AC adaptor Do not place the adaptor directly onto a ceiling panel or other such
surface. Extreme danger is posed when water has collected on the surface as a result of leaking rain, for instance. Secure the adaptor firmly to the bottom or other surface of a reinforcing member made of channel steel where dust and other foreign matter will not accumulate. ( page 13)
Secure the adaptor firmly so that there will be no chance that it will fall off or fall down. Secure it using a strength which can withstand the mass of the AC adaptor.
Install the accessory AC adaptor near the main power outlet, and position it in such a way that its power plug can be plugged into and unplugged from the outlet easily. When connecting the AC adaptor to a power outlet on the ceiling or on any other surface where dust may collect, wipe off the dust on the power plug at periodic intervals as an antitracking measure.
Power switch This unit does not have a power switch. When the power is supplied, the pan, tilt, zoom and focusing operations are performed.*1 Before proceeding with maintenance, be absolutely sure to disconnect the power plug from the power outlet.
*1 Under factory default conditions, the unit will be in Standby mode when power is supplied for the first time. (Status display lamp: Lit orange)
When the power supply is cut off while the unit is in Standby mode, the unit will be in Standby mode the next time power is supplied. (Status display lamp: Lit orange)
When the power supply is cut off while the unit is in Power ON mode, the unit will be in Power ON mode the next time power is supplied. (Status display lamp: Lit green)
(For details, refer to How to turn the power on and off ( page 51).)
Connecting the power cable Be absolutely sure to connect the power cable of the AC adaptor through a circuit breaker using one of the following methods. (1) Connect the power cable through a power control unit. (2) Connect the power cable to a circuit breaker in a power
distribution panel with a contact distance of 3.0 mm (1/8 inches) or more.
Use a circuit breaker which is capable of shutting off all the poles of the main power supply with the exception of the protective ground conductor.
(3) Install the AC adaptor near the power outlet, and connect it through the power plug.
Grounding Before operating the unit, check that SIGNAL GND has been securely grounded.
If there is a possibility of noise interference Either wire the cables so that the power cable (ceiling light cord) of AC 100 V or more, and the signal cable are placed at least 1 meter (3.3 ft) apart. Alternatively run each cable through its own metal conduit. (The metal conduits must be grounded.)
Radio signal interference If the unit is positioned near a TV or radio transmitting antenna or a strong electrical field or magnetic field (such as that generated by a motor, transformer or power lines), its images may be distorted and/ or the images may be affected by noise.
When connecting the cables, ensure that the connector areas will not be subject to any load. Doing so may cause malfunctioning.
Allowing the generated heat to escape This unit allows the heat generated inside to escape from its surfaces. Do not install the unit in a location where it will be surrounded by walls or other surfaces and where heat will be trapped. In addition, the heat is dissipated to the bottom panel which will warm up over time: This is normal and not indicative of any trouble.
PoE++ power supplies Use a PoE++ (IEEE 802.3bt compliant) compatible hub or power supply device.
Network settings The network function of this unit does not work unless an initial account is set up (except when using the Easy IP Setup Software ( page 48)). A personal computer is required to set up an initial account. ( page 50) Network connection with AWRP150 or AWRP60 requires setup
of an initial account. ( page 50) When an initial account is not set up, AWRP150 or AWRP60 can detect but cannot control this unit.
6
Installation precautions (continued)
Installation Instructions
Before installation
Be sure to configure the switches on the connector panel and bottom of the unit before installing it. Configuring the switches after the unit is installed may prove difficult.
IR ID switch settings The IR ID switches are located on the connector panel of the unit.
DC IN 12 V
IR ID
AUDIO IN RS-422
SERVICE 12G SDI OUT3G SDI OUT
G/L IN
LAN LINK ACT
IR ID switch
CAM1 CAM2 CAM3 CAM4
These are used to select the ID of the wireless remote control (optional accessory). ( page 47) The IR ID switch settings CAM1 to CAM4 correspond to the
Service switch settings The service switches are located on the connector panel of the unit. Perform switch settings before turning the unit on.
DC IN 12 V
IR ID
AUDIO IN RS-422
SERVICE 12G SDI OUT3G SDI OUT
G/L IN
LAN LINK ACT
SW1
ON
OFF
SW2 SW3 SW4
Service switch
Function Factory settings SW1 Switches for initialization
(Refer to the explanations in Initialization 1 and Initialization 2)
OFF
SW2 Always leave at OFF (used for factory adjustments)
OFF SW3 OFF SW4 OFF
Initialization 1 Reset the user authentication settings and host authentication settings
for network connection. (This will delete all the registered user information (IDs/passwords) and host information (IP addresses).)
With the IR ID switches and service switches set as shown below, turn on the power of the unit.
SW1
ON
OFF
SW2 SW3 SW4
When initialization is complete, the status display lamp on the front of the unit blinks green. Set the service switches back to their original positions (SW1 to SW4 all OFF), then restart the unit.
Initialization 2 The unit is reset to the state it was in at the time of purchase. (All
camera menu setting values and network setting values are reset.) With the IR ID switches and service switches set as shown below, turn
on the power of the unit. SW1
ON
OFF
SW2 SW3 SW4
When initialization is complete, the status display lamp on the front
of the unit blinks green. Set the service switches back to their original positions (SW1 to SW4 all OFF), then restart the unit.
Setting the installation method (Desktop or Hanging) from the OSD menu
Set Desktop or Hanging in [Install Position] on the [Pan/Tilt 1/2] screen from the OSD menu of this unit.
Pan/Tilt 1/2
Install Position Desktop Smart Picture Flip Off Flip Detect Angle 90deg P/T Speed Mode Normal(60deg/s) P/T Acceleration Setting Speed With Zoom Position On Focus Adjust With PTZ. Off Privacy Mode Off
Return
Install Position [Desktop, Hanging]
[Desktop] or [Hanging] is selected here as the method used to install the unit. Desktop Stand-alone installation Hanging Suspended installation
When [Hanging] has been selected, the top, bottom, left and right
of the images will be reversed, and up/down/left/right control for panning and tilting will also be reversed.
6 7
Installation Instructions
Be absolutely sure to read through the Read this first! ( page 4) and Installation precautions ( pages 5 to 6).
The procedure given here is for the kind of installation where the unit is suspended from an overhead surface, but the same steps are followed for a standalone installation.
If the ceiling panel is not strong enough to bear the units weight, use the kind of mount bracket that is supported by anchor bolts between the concrete ceiling and ceiling panel. The unit supports the WV-Q105A direct ceiling mount bracket which is used solely for combination cameras. Use this bracket to install the unit. ( page 13) In a case like this, the holes ( 60 mm ( 2-3/8 inches)) for installing the direct ceiling mount bracket on the ceiling must be drilled in the ceiling panel. It is also recommended that you provide an inspection space or opening for access purposes in the area near where the equipment is installed in order to facilitate installation and the wiring connections work. For details on supplied accessories, refer to the page 31.
1. Check the mounting space. Refer to the illustration, and determine where the unit is to be installed and in which direction it should be mounted.
Factor in the unit mounting area and include space for the wires extending from its rear panel. The asterisk () in the illustration marks the position and dimensions of the hole for mounting the mount bracket.
130 (5-4/32) (Space for the wires from the
rear panel)
29 0
(1 1-
13 /3
2) o
r m or
e (S
pa ce
fo r t
he w
ire s)
Hole for checking the positioning
The front panel of the unit on this side.
Unit: mm (inch)
Mount bracket
Hook for mounting the drop-prevention wire Unit mounting area
Through-hole for cable 40 ( 1-9/16) (reference)
() Holes for mounting the mount bracket: 4.5 ( 3/16) 4
Hole for mounting the main unit mounting screw
Hole for installing the WV-Q105A direct ceiling mount bracket ( 60 ( 2-3/8))
80 (3
-5 /3
2)
78 (3
-2 /3
2)
77 (3
-1 /3
2)
65 (2
-1 8/
32 )
(1 -2
6/ 32
)
() 83.5 (3-9/32)
156 (6-5/32)
160 (6-10/32)
( ) 4
6
90 (3
-1 7/
32 )
99 (3
-2 9/
32 )
66 (2-19/32)
Before proceeding to install and connect the main unit, connect the LAN cable, HDMI cable and coaxial cables in the space above the ceiling panel,
and then pass the cables through the cable holes. For a power outlet which is used on the ceiling, be absolutely sure to take measures to deal with the tracking that may be caused by the accumulation
of dust and other foreign matter.
How to install and connect the unit
8
Installation Instructions
2. Mount the mount bracket onto the installation surface. Use the bracket mounting screws (M4, bindhead: 10 mm (13/32 inches) long) supplied with the unit. For proper clamping torque, securely attach the screws using the specified tools.
Screw diameter Clamping torque
M4 1.47 N m {15 kgf cm}
Bracket mounting screws 4 (supplied) (M4, bind-head)
Use only the screws supplied with the unit. Do not use any other screws such as wood screws, nails, etc.
3. Attach the drop-prevention wire. Pull out the drop-prevention wire from the bottom panel of the unit, and engage the end with the wire ring through the hole of the mount bracket
hook. Pull the dropprevention wire, and check that it has been attached securely to the hook.
End of hook
Holding spring
Pull out the drop-prevention wire, and engage it with the mount bracket hook.
Drop-prevention wire
Do not do this work while holding the camera head since doing so may result in malfunctioning of the unit. The drop-prevention wire is designed to be used for installation where the unit is suspended from an overhead surface so do not subject it to the
weight of units other than the unit.
8 9
How to install and connect the unit (continued)
Installation Instructions
4. Mount the unit. Align the position of the hole for checking the positioning with the status display lamp. Align the holes on the camera main unit used to insert the bottom panel with the protrusions on the mount bracket used for inserting the camera,
push the bracket and camera firmly together, and rotate the main unit by about 15 degrees in the direction of the arrow. Secure the mount bracket to the unit using the main unit mounting screw (M3) as supplied. Attach the mount bracket securely with the prescribed tool using the clamping torque below. Be absolutely sure to verify that none of the screws are loose.
Screw diameter Clamping torque
M3 0.78 N m {8 kgf cm}
Main unit mounting screw (M3 screw) (with flat washer, spring washer)
Status display lamp
Approx. 15
On the camera main unit: Holes (3) used to insert the bottom panel
On the mount bracket: Protrusions (3) used for inserting the camera
Hole for checking the positioning
Do not do this work while holding the camera head since doing so may result in malfunctioning of the unit. Use only the screws supplied. Do not use any other screws. Check that the unit has been mounted securely with no tilting or wobbling. The unit must be secured without fail using the main unit mounting screw before any of the cables are connected.
5. Check the mounting. Check out the following points.
The main unit mounting screw must be mounted securely. The unit must not tilt, and it must be mounted exactly. The unit must be securely installed. The unit pedestal part must not rotate even when an attempt
is made to turn it.
10
How to install and connect the unit (continued)
Installation Instructions
6. Connect the rear panel connectors. Anchor the AC adaptor cable in place using the cable clamp. Do not connect PoE cable to the RS422 port. For details on recommended products, refer to the catalog or consult your local dealer. Always disconnect the power supply before connecting or disconnecting cables.
Connecting or disconnecting cables while the power is turned on may result in malfunctions.
LAN cable
AC adaptor cable
HDMI cable
Coaxial cable
zHow to secure the AC adaptor cable
A Loosely secure the cable clamp.
Cable clamp
Loosely secure the cable clamp in the area shown above.
B Fasten the cable clamp.
Strap part
Take hold of the strap part, slide the cable clamp until it stops moving, and then secure it tightly.
10 11
How to install and connect the unit (continued)
Installation Instructions
7. Attach the cable cover. Fit the two protrusions on the cable cover into the guides on either side of the camera main unit rear panel. Using the two screws (M3) supplied with the cable cover, secure the cable cover to the camera main unit. Attach the mount bracket securely with the prescribed tool using the clamping torque below. Be absolutely sure to verify that none of the screws are loose.
Screw diameter Clamping torque
M3 0.78 N m {8 kgf cm}
Protrusion
Guide
Cable cover
Screw (M3)
Be sure to tighten to the specified torque. Check that the unit has been mounted securely with no wobbling.
zMake the setting for Desktop/Hanging for reflecting the installed status on this unit. When performing operations from a wireless remote control A Press one of the
Installation Instructions
When using the WV-Q105A (optional accessory) It is recommended that you provide an inspection opening or other such space for access purposes in the area near where the equipment is installed in order to facilitate installation and the wiring connections work. Before mounting the mount bracket, check that the installation location is strong enough to withstand the total mass (approx. 2.7 kg (5.94 lb)) which will be exerted once the camera is mounted. Use the mount bracket where the space between the ceiling panel and the concrete ceiling is at least 100 mm (315/16 inches) high. The bracket can be mounted where the thickness of the ceiling panel ranges from 5 mm (3/16 inches) to 40 mm (19/16 inches). The dropprevention wire (supplied with the WVQ105A) must be used when mounting the direct ceiling mount bracket.
Height above ceiling panel: At least 100 mm (3-15/16 inches)
The anchor bolts must not protrude beneath the ceiling panel.
Ceiling panel (plasterboard, etc. with a thickness from 5 mm (3/16 inches) to 40 mm (1-9/16 inches))
Anchor bolts (Withdrawal strength: 133 N {13.5 kgf} or more)
60 mm (2-3/8 inches)
Concrete ceiling
1. Refer to the Operating Instructions of the WV-Q105A direct ceiling mount bracket, and attach the WV-Q105A as well as the drop-prevention wire angle and drop-prevention wire supplied with the WV-Q105A to the anchor bolts.
Mounting the anchor bolts and direct ceiling mount bracket () This job is facilitated if the direct ceiling mount bracket is loosely secured to the ceiling panel in one place, and the direct ceiling mount bracket and anchor bolts are vertically aligned before the nuts are tightened up.
2. First, remove the screws which were loosely fastened in step 1, and then align the camera mount bracket of the AW-UE100 with the screw holes in the WV-Q105A direct ceiling mount bracket and mount it in place. Use the mounting screws (the M4L60 Phillips head screws with adhesive) supplied with the WVQ105A as the mounting screws. Fasten the AC adaptor securely to the bottom or other surface of the reinforcing member made of channel steel where dust and other foreign matter
will not accumulate. Do not place the AC adaptor directly onto the ceiling panel or other such surface.
Drop-prevention wire angle (Supplied with WV-Q105A) Direct ceiling mount bracket WV-Q105A (optional accessory)
Drop-prevention wire (Supplied with WV-Q105A)
Plasterboard or other ceiling panel
Camera mount bracket (Supplied with AW-UE100)
Mounting screw 4 (Supplied with WV-Q105A)
Inspection opening recommended The installation and wiring connection
work is facilitated if an inspection opening is provided for access purposes.
(): Fasten here using the nut.
Anchor bolts
Space above the ceiling
AW-UE100
Channel steel
Secure the AC adaptor firmly to a member made of channel steel.
(Ceiling panel)
3. Install the AW-UE100 camera by following the procedure starting with step 3 on page 9.
12 13
How to install and connect the unit (continued)
Installation Instructions
Removing the camera
1. Turn off the circuit breaker and power.
2. Disconnect the cables. Disconnect the LAN cable, and HDMI cable, etc.
3. Remove the main unit mounting screw used to secure the unit and mount bracket.
4. Push the unit (A). Turn it approximately 15 degrees away from the installed position (B), and remove it (C).
Main unit mounting screw (M3 screw) (with flat washer, spring washer)
Approx. 15
Do not do this work while holding the camera head since doing so may result in malfunctioning of the unit.
5. Disengage the drop-prevention wire from the mount bracket.
A Pull the dropprevention wire in the direction shown by the arrow above.
B Twist the wire, and remove the wire loop through the opening in the hook.
C Pull the wire in the direction shown by the arrow above, and simply pull it out.
14
Installation Instructions
Stand-alone installation (when the mount bracket is going to be used)
The same steps are followed as for the kind of installation where the unit is suspended from an overhead surface ( pages 8 to 11).
1. Check the mounting space. As with installing the unit suspended from an overhead surface, carefully check the space where the unit will be mounted, and then decide if it is
appropriate to install the unit in that space.
2. Mount the mount bracket onto the installation surface.
Bracket mounting screws 4 (supplied) (M4, bind-head)
3. Attach the drop-prevention wire.
4. Mount the unit. Align the position of the hole for checking the positioning with the status display lamp. Align the holes on the camera main unit used to insert the bottom panel with the protrusions on the mount bracket used for inserting the camera,
push the bracket and camera firmly together, and rotate the main unit by about 15 degrees in the direction of the arrow. Secure the mount bracket to the unit using the main unit mounting screw (M3) as supplied.
Main unit mounting screw (M3 screw) (with flat washer, spring washer)
Status display lamp
On the camera main unit: Holes (3) used to insert the bottom panel
On the mount bracket: Protrusions (3) used for inserting the camera
Hole for checking the positioning
Attach the drop-prevention wire.
Approx. 15
14 15
Installation Instructions
5. Check the mounting.
6. Connect the rear panel connectors. Do not connect PoE cable to the RS422 port. For details on recommended products, refer to the catalog or consult your local dealer. Always disconnect the power supply before connecting or disconnecting cables.
Connecting or disconnecting cables while the power is turned on may result in malfunctions.
Coaxial cable
HDMI cable
AC adaptor cable
LAN cable
zHow to secure the AC adaptor cable
A Loosely secure the cable clamp.
Cable clamp
Loosely secure the cable clamp in the area shown above.
B Fasten the cable clamp.
Strap part
Take hold of the strap part, slide the cable clamp until it stops moving, and then secure it tightly.
16
Stand-alone installation (when the mount bracket is going to be used) (continued)
Installation Instructions
7. Attach the cable cover. Fit the two protrusions on the cable cover into the guides on either side of the camera main unit rear panel. Using the two screws (M3) supplied with the cable cover, secure the cable cover to the camera main unit. Attach the mount bracket securely with the prescribed tool using the clamping torque below. Be absolutely sure to verify that none of the screws are loose.
Screw diameter Clamping torque
M3 0.78 N m {8 kgf cm}
Protrusion
Guide
Cable cover
Screw (M3)
Be sure to tighten to the specified torque. Check that the unit has been mounted securely with no tilting.
16 17
Stand-alone installation (when the mount bracket is going to be used) (continued)