Mitsubishi Electric Rotary Servo v2 User's Manual

Rotary Servo Motor User's Manual (HG-KNS/HG-SNS)

-HG-KNS_ -HG-SNS_

Mitsubishi Electric AC Servo System

SAFETY INSTRUCTIONS (Please read the instructions carefully before using the equipment.)

To use the equipment correctly, do not attempt to install, operate, maintain, or inspect the equipment until you have read

through this manual, installation guide, and appended documents carefully. Do not use the equipment until you have a full

knowledge of the equipment, safety information and instructions.

In this manual, the safety instruction levels are classified into "WARNING" and "CAUTION".

Note that the CAUTION level may lead to a serious consequence depending on conditions.

Please follow the instructions of both levels because they are important to personnel safety.

Forbidden actions and required actions are indicated by the following diagrammatic symbols.

In this manual, precautions for hazards that can lead to property damage, instructions for other functions, and other

information are shown separately in the "POINT" area.

After reading this guide, keep it accessible to the operator.

WARNING Indicates that incorrect handling may cause hazardous conditions, resulting in death or severe injury.

CAUTION Indicates that incorrect handling may cause hazardous conditions, resulting in medium or slight injury.

Indicates a forbidden action. For example, "No Fire" is indicated by .

Indicates a required action. For example, grounding is indicated by .

1

2

[Installation/wiring]

[Installation/wiring]

[Maintenance]

DISPOSAL OF WASTE Please dispose of this product and other options according to your local laws and regulations.

CABLES USED FOR WIRING Wires mentioned in this manual are selected based on the ambient temperature of 40 C.

U.S. CUSTOMARY UNITS U.S. customary units are not shown in this manual. Convert the values if necessary according to the following table.

WARNING To prevent an electric shock, turn off the power and wait for 15 minutes or more before starting wiring

and/or inspection.

To prevent an electric shock, ground the rotary servo motor securely.

To prevent an electric shock, any person who is involved in wiring should be fully competent to do the

work.

To prevent an electric shock, do not attempt to wire the rotary servo motor until it has been mounted.

To prevent an electric shock, do not touch the conductive parts.

CAUTION To prevent injury, do not touch the rotor of the rotary servo motor during operation.

To prevent injury, transport the products correctly according to their mass.

To prevent injury, do not touch any sharp edges such as the sharp edges of the rotary servo motor

with bare hands when handling the rotary servo motor.

WARNING To prevent an electric shock, any person who is involved in inspection should be fully competent to do

the work.

Quantity SI (metric) unit U.S. customary unit

Mass 1 [kg] 2.2046 [lb]

Length 1 [mm] 0.03937 [inch]

Torque 1 [Nm] 141.6 [ozinch]

Moment of inertia 1 [( 10-4 kgm2)] 5.4675 [ozinch2]

Load (thrust load/axial load) 1 [N] 0.2248 [lbf]

Temperature N [C] 9/5 + 32 N [F]

C O

N T

E N

T S

CONTENTS SAFETY INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

DISPOSAL OF WASTE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

CABLES USED FOR WIRING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

U.S. CUSTOMARY UNITS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

CHAPTER 1 INTRODUCTION 6

1.1 Model designation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

1.2 Rating plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

1.3 Environment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

1.4 Parts identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

1.5 Electromagnetic brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

1.6 Rotary servo motor shaft shapes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

1.7 Instructions on storage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

1.8 Instructions on maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

1.9 Instructions on protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

CHAPTER 2 INSTALLATION 14

2.1 Mounting direction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

2.2 Load mounting/dismounting precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

2.3 Permissible load for the shaft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

2.4 Protection from oil and water. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

2.5 Cable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

2.6 Rotary servo motors with an oil seal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

2.7 Inspection items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Periodic inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

2.8 Parts with a service life. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

2.9 Machine accuracy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

2.10 Mounting rotary servo motors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

2.11 Restrictions when using this product at an altitude exceeding 1000 m and up to 2000 m . . . . . . . . . . . . 20

CHAPTER 3 CONNECTORS USED FOR ROTARY SERVO MOTOR WIRING 21

3.1 Selection of connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

3.2 Wiring connectors (connector configurations A/B/C) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

3.3 Wiring connectors (connector configurations D/E/F/G) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

CHAPTER 4 CONNECTION OF SERVO AMPLIFIER AND ROTARY SERVO MOTOR 27

4.1 Precautions for wiring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

4.2 Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

HG-KNS series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

HG-SNS series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

4.3 Selection example of wires. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

CHAPTER 5 WIRING OPTION 35

5.1 Cable/connector sets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Combinations of cable/connector sets. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Cable and connector list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

5.2 Encoder cable/connector sets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

3

4

MR-J3ENCBL_M-_-_. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

MR-J3JCBL03M-_-L . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

MR-J3JSCBL03M-_-L . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

MR-EKCBL_M-_ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

MR-J3ENSCBL_M-_ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

5.3 Servo motor power cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

5.4 Electromagnetic brake cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

5.5 Wires for option cables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

5.6 Shield procedure of CN2 side connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

CHAPTER 6 HG-KNS SERIES 61

6.1 Standard specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Standard specifications list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Torque characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

6.2 Combinations of servo amplifiers and rotary servo motors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

6.3 Characteristics of electromagnetic brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

6.4 Rotary servo motors with special shafts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Keyed shaft (with double round-ended key) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

D cut shaft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

6.5 Rotary servo motors with an oil seal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

6.6 Mounting connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

6.7 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Standard (without an electromagnetic brake) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

With an electromagnetic brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

CHAPTER 7 HG-SNS SERIES 77

7.1 Standard specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Standard specifications list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Torque characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

7.2 Combinations of servo amplifiers and rotary servo motors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

7.3 Characteristics of electromagnetic brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

7.4 Rotary servo motors with special shafts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

Keyed shaft (without key) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

7.5 Rotary servo motors with an oil seal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83

7.6 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84

Standard (without an electromagnetic brake) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84

With an electromagnetic brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87

CHAPTER 8 COMPLIANCE WITH EACH REGION 90

8.1 Compliance with CE marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90

CE marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90

For compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90

8.2 Compliance with UL/CSA standard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91

Flange size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91

Selection example of wires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91

CHAPTER 9 APPENDIX 92

9.1 Rotary servo motor ID codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92

9.2 Selection example of rotary servo motor power cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93

9.3 Connector dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94

C O

N T

E N

T S

9.4 Fabrication of the encoder cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100

REVISIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .102

WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .103

TRADEMARKS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .104

5

6

1 INTRODUCTION

1.1 Model designation The following describes model designation. Not all combinations of the symbols are available.

*1 For the HG-SNS series, the key is not included.

K

D

B

J

H G - K N S 1 3 B J D

2

3

1

2

4

5

7

10

15

20

30

2000

3000

0.1

0.2

0.4

0.5

0.75

1.0

1.5

2.0

3.0

HG-KNS

HG-SNS

Shaft type

Symbol Shaft shape

None

D cut shaft

None Not attached

Electromagnetic brake

Symbol Electromagnetic brake

Attached

None Not attached

Oil seal

Symbol Oil seal

Attached

Keyed shaft *1

Standard (straight shaft)

Rated speed

Symbol Rated speed [r/min]

Rated output

Symbol Rated output [kW]

Series Feature

Low inertia/small capacity

Medium inertia/medium capacity

1 INTRODUCTION 1.1 Model designation

1

The production year and month of the rotary servo motor are indicated in the serial number on the rating plate.

The year and month of manufacture are indicated by the last two digits of the year and one digit of the month [1 to 9, X (10), Y

(11), and Z (12)].

For October 2019, the serial number would be "SER. _ _ _ _ _ _ _ _ _ 19X".

The following shows an example of the rating plate for explanation of each item.

HG-KNS13J 112 0.8

0.57

31 98

MADE IN JAPAN FABRIQU AU JAPON

100W

SER.M00001234 19X

Model Input power supply, Rated current,

Rated output Mass, Insulation class

Rated speed Induced voltage constant,

Maximum ambient temperature Power factor, IP rating

Serial number Country of origin,

Conforming standards

Manufacturer

1 INTRODUCTION 1.2 Rating plate 7

8

1.3 Environment

*1 Do not use in an environment where there is exposure to oil mist, oil, and water. *2 Refer to the following for restrictions on using this product at an altitude exceeding 1000 m above sea level.

Page 20 Restrictions when using this product at an altitude exceeding 1000 m and up to 2000 m

Condition Operation Storage

Ambient temperature 0 C to 40 C (non-freezing) -15 C to 70 C (non-freezing)

Ambient humidity 10 %RH to 80 %RH (non-condensing) 10 %RH to 90 %RH (non-condensing)

Ambience *1 Indoors (no direct sunlight); no corrosive gas, inflammable gas, oil mist or dust

Altitude 2000 m or less *2

Vibration resistance Refer to the following.

Page 61 Standard specifications

Page 77 Standard specifications

1 INTRODUCTION 1.3 Environment

1

HG-KNS series

*1 The encoder cable and power supply cable are options. *2 An electromagnetic brake cable is also required for servo motors with an electromagnetic brake.

HG-SNS series

*1 An electromagnetic brake connector is also provided for servo motors with an electromagnetic brake.

Power cable *1 *2

Power lead (U/V/W) Grounding lead

Servo motor shaft

Encoder cable *1

Encoder

Power connector *1

Power supply (U/V/W) Grounding ( )

Servo motor shaft

Encoder connector

Encoder

1 INTRODUCTION 1.4 Parts identification 9

10

1.5 Electromagnetic brake The rotary servo motor with an electromagnetic brake can be used to prevent a drop in vertical lift applications or to ensure

double safety at an emergency stop, for example. When operating the rotary servo motor, supply power to the

electromagnetic brake to release the brake. Switching power off enables the electromagnetic brake.

Precautions

The electromagnetic brake on the rotary servo motor is designed to hold the motor shaft and should not be used for

ordinary braking.

Incorrect wiring, service life, or the mechanical structure (e.g. where a ball screw and the rotary servo motor are coupled via

a timing belt) may cause the electromagnetic brake to be unable to hold the motor shaft. To ensure safety, install a stopper

on the machine side.

If it is assumed that a power failure or product malfunction may result in a hazardous situation, use a rotary servo motor

with an electromagnetic brake or provide an external brake system for holding purpose to prevent such hazard.

Configure an electromagnetic brake circuit which is interlocked with an external emergency stop switch.

The electromagnetic brake is provided to prevent a drop at a power failure or servo alarm occurrence during vertical drive

or to hold a shaft at a stop. Do not use it for normal braking (including braking at servo-lock).

The electromagnetic brake has a time lag. Ensure enough time between releasing the electromagnetic brake and starting

the rotary servo motor. Be sure to check the operation delay time with an actual machine.

For details of the circuit configuration and timing chart, refer to the following.

MR-JET User's Manual (Hardware)

When the electromagnetic brake is released, the temperature of the rotary servo motor may increase regardless of driving.

The service life of the brake may be shortened under sudden acceleration/deceleration conditions.

Electromagnetic brake power supply Prepare the following power supply for use with the electromagnetic brake only. The electromagnetic brake terminals (B1 and

B2) have no polarity.

A surge absorber (VAR) must be installed between B1 and B2. For a selection example of surge absorbers, refer to the

"Characteristics of electromagnetic brake" section appropriate for the rotary servo motor series being used.

When a diode is used as a surge absorber, the electromagnetic braking time becomes longer.

Sound generation The brake lining may rattle during a low-speed operation; however, it poses no functional problem.

The noise may be reduced or eliminated by the machine resonance suppression filter set with the servo amplifier parameters.

For details, refer to "Machine resonance suppression filter" in the following manual.

MR-JET User's Manual (Adjustment)

U

RA

B

Contacts must be opened when ALM (Malfunction) or MBR (Electromagnetic brake interlock) turns off.

Contacts must be opened with the emergency stop switch.

Rotary servo motor

Electromagnetic brake

24 V DC

VAR

B1

U B

B2

VAR

B1

U B

B2

E le

ct ro

m ag

ne tic

b ra

ke

E le

ct ro

m ag

ne tic

b ra

ke

Switch Switch 24 V DC power supply for electromagnetic brake

24 V DC power supply for electromagnetic brake

or

1 INTRODUCTION 1.5 Electromagnetic brake

1

Selection condition

Tentative selection and verification of surge absorber Maximum permissible circuit voltage of varistor

Tentatively select a varistor whose maximum permissible voltage is larger than Vb [V].

Brake current (Ib)

Energy (E) generated by brake coil

Varistor limit voltage (Vi)

From the energy (E) generated in the brake coil and the varistor characteristic diagram, calculate the varistor limit voltage (Vi)

when the brake current (Ib) flows into the tentatively selected varistor during opening of the circuit.

Vi is favorable when the varistor limit voltage (Vi) [V] is smaller than the desired suppressed voltage (Vs) [V].

If Vi is not smaller than Vs, reselect a varistor or improve the withstand voltage of devices.

Surge current width ()

Given that the varistor absorbs all energies, the surge current width () is as follows.

Examining surge life of varistor

From the varistor characteristic diagram, find the guaranteed current value (Ip) in which the number of the surge application

life is N at the surge current width (). Calculate the guaranteed current value (Ip) ratio (Ip/Ib) to brake current (Ib).

If a sufficient margin is ensured for Ip/Ib, the number of the surge application life N [time] can be considered as favorable.

Other precautions A leakage magnetic flux occurs at the shaft end of the servo motor with an electromagnetic brake. Note that chips, screws,

and other debris are attracted.

Item Condition

Electromagnetic brake specification R []: Resistance

L [H]: Inductance

Vb [V]: Power supply voltage

Desired suppression voltage Vs [V] or less

Durable surge application time N times

U

Relay

Varistor Brake coil24 V DC

Vb Ib = [A]

R

L Ib2

E = [J] 2

Vi Ib = [S]

E

1 INTRODUCTION 1.5 Electromagnetic brake 11

12

1.6 Rotary servo motor shaft shapes There are three shaft shape types for the rotary servo motor: keyed shaft (with double round-ended key), keyed shaft (without

key), and D cut shaft.

To prevent damage to the shaft, do not use the keyed shaft (with double round-ended key), keyed shaft (without key), and D

cut shaft for frequent start/stop applications. Use a friction coupling or the like when coupling the shaft with a machine.

Keyed shaft (with double round-ended key)

Keyed shaft (without key)

D cut shaft

Straight shaft

A

A Section AA

A

A Section AA

1 INTRODUCTION 1.6 Rotary servo motor shaft shapes

1

Precautions

Note the following when storing the rotary servo motor for an extended period of time (guideline: three or more months).

Always store the linear servo motor indoors, in a clean and dry place.

When storing in a dusty and humid area, take measures such as covering the whole product.

If the insulation resistance of the winding decreases, check how to store the equipment.

Although the servo motor has been given rust prevention treatment with paint and preventive oil before shipment, rust may

still appear depending on the storage period and conditions. If the servo motor is to be stored for longer than six months,

apply rust prevention oil again, especially to the machined surfaces of the shaft and other parts.

Before using the product after storage for an extended period of time, hand-turn the rotary servo motor output shaft , and

check to ensure that there is no abnormality. For the rotary servo motor with an electromagnetic brake, check it after

releasing the electromagnetic brake with the brake power supply.

When the product has been stored for an extended period of time, contact your local sales office.

1.8 Instructions on maintenance

Precautions

To prevent the scuffed surface, do not scratch the coated surface with hard objects nor clean the coated surface with an

organic solvent.

For repair and parts replacement, contact your local sales office.

1.9 Instructions on protection

Precautions

Provide an adequate protection to prevent unexpected restart after an instantaneous power failure.

1 INTRODUCTION 1.7 Instructions on storage 13

14

2 INSTALLATION

Precautions

Install the rotary servo motor on incombustible material. Installing them directly or close to combustibles will lead to smoke

or a fire.

Provide an adequate protection to prevent screws and other conductive matter, oil and other combustible matter from

entering the rotary servo motor.

The temperature of the rotary servo motor may exceed 100 C depending on the operating method. Take safety measures

such as providing covers.

The eyebolts of the rotary servo motor are only for transportation of the rotary servo motor.

Do not use them to transport the rotary servo motor when it is mounted on a machine.

Do not overtighten the eyebolts of the rotary servo motor. To prevent damage to the tap, avoid tightening too hard.

Stacking in excess of the specified number of product packages is not allowed.

Do not hold the cables, connectors, shaft, or encoder when carrying the rotary servo motor. Otherwise, it may drop.

Install the rotary servo motor in a load-bearing place in accordance with the user's manual.

Do not install or operate the rotary servo motor which has been damaged or have any parts missing.

Securely fix the rotary servo motor to a machine. If attached insecurely, the motor may come off during operation.

To prevent a connection failure, malfunction, or similar problem, do not strike the connector.

Be sure to measure the motor vibration level with the rotary servo motor mounted on a machine when checking the

vibration level. A great vibration may cause early damage to a bearing, encoder, and brake. The great vibration may also

cause the poor connector connection or bolt looseness.

For the gain adjustment at the equipment startup, check the torque waveform and the speed waveform with a

measurement device to check that no vibration occurs. If the vibration occurs due to high gain, the vibration may cause

early damage to the rotary servo motor.

Use the product within the specified environment. For the environment conditions, refer to the specifications of the rotary

servo motor series.

To prevent a malfunction on the encoder, do not apply shocks, e.g. hit with a hammer, when coupling the shaft end of the

rotary drive motor.

To prevent the shaft from being broken, do not subject the shaft of the rotary servo motor to more than the permissible load.

To prevent the shaft from being broken and bearing from being worn out, do not use a rigid coupling when coupling a load

to the rotary servo motor.

To prevent vibration during rotary servo motor operation, or the cause of a damage to the bearings and encoder, the

balance level of the load needs to be as even as possible.

To prevent a malfunction, do not use the rotary servo motor where the shaft-through portion may be subject to pressure

(e.g. compressed air).

Take safety measures such as provide covers, to prevent accidental access to the rotor of the rotary servo motor during

operation.

Do not get on or put heavy load on the equipment.

Do not drop or strike the rotary servo motor.

To prevent a fire or injury from occurring in case of an earthquake or other natural disasters, securely install, mount, and

wire the linear servo motor in accordance with the user's manual.

Do not disassemble, repair, or modify the product.

The equipment must be installed in the specified direction.

2 INSTALLATION

2

2.1 Mounting direction The mounting direction of the rotary servo motor is shown in the following table.

It is recommended that the connector section be set downward for mounting the rotary servo motor in the horizontal direction.

Examine the cable clamping method, and give a gentle slack to the connection cable, to prevent excessive load from being

applied to the connector and cable connection part.

Rotary servo motor with an electromagnetic brake The rotary servo motor with an electromagnetic brake can also be mounted in the same directions as the one without an

electromagnetic brake. When the servo motor with an electromagnetic brake is mounted with the shaft end upward, the brake

plate may generate sliding sound but it is not a fault.

Rotary servo motor series Mounting direction

HG-KNS

HG-SNS

All directions

Slack

2 INSTALLATION 2.1 Mounting direction 15

16

2.2 Load mounting/dismounting precautions When mounting a pulley to the rotary servo motor with a keyed shaft, use the screw hole in the shaft end. To fit the pulley,

first insert a double-end bolt into the screw hole of the shaft, put a washer against the end face of the coupling, and insert

and tighten a nut to force the pulley in.

For shafts without a keyway, use a friction coupling or the like for coupling the rotary servo motor with a load.

When removing the pulley, use a pulley remover to protect the shaft from excessive load and impact.

To ensure safety, fit a protective cover or the like on the rotary area, such as the pulley, mounted to the shaft.

When a threaded shaft end part is needed to mount a pulley on the shaft, please contact your local sales office.

The direction of the encoder on the rotary servo motor cannot be changed.

When mounting the rotary servo motor, use spring washers or similar parts and fully tighten the bolts so that they do not

become loose due to vibration.

Precautions

To prevent a malfunction on the encoder, the shaft end must not be hammered during assembling.

Do not process the shaft to avoid damage to the encoder and bearing.

2.3 Permissible load for the shaft For the permissible load for the shaft specific to the rotary servo motor, refer to the chapter of the rotary servo motor series.

Use a flexible coupling and adjust the misalignment of the shaft to less than the permissible radial load.

When using a pulley, sprocket, or timing belt, keep the radial load within the permissible value.

Exceeding the permissible load can cause deterioration of the bearing and damage to the shaft.

The load indicated in this section is static load in a single direction and does not include eccentric load. To prevent the

rotary servo motor being damaged, make eccentric load as small as possible.

Precautions

Do not use a rigid coupling as it may apply excessive bending load to the shaft of the rotary servo motor, leading the shaft to

break and the bearing to wear out.

Rotary servo motor

Double-end stud

Nut

Washer Pulley

2 INSTALLATION 2.2 Load mounting/dismounting precautions

2

2.4 Protection from oil and water Provide adequate protection to prevent foreign matter, such as oil from entering the rotary servo motor shaft. When installing

the rotary servo motor, consider the items in this section.

Do not use the rotary servo motor with its cable soaked in oil or water.

When the servo motor is to be installed with the shaft end upward, provide measures so that it is not exposed to oil and

water entering from the machine side, gear box, etc.

If oil such as cutting oil splashes on the servo motor, the sealant, packing, cable, and other parts may be affected

depending on the oil type.

In the environment where the rotary servo motor is exposed to oil mist, oil, or water, the rotary servo motor of the standard

specifications may not be usable. Please contact your local sales office.

2.5 Cable The power supply and encoder cables routed from the rotary servo motor should be fixed to the rotary servo motor to keep

them unmovable. Otherwise, the cable may be disconnected. In addition, do not modify the connectors, terminals, and other

areas at the ends of the cables.

Precautions

The cables should not be damaged, stressed, loaded, or pinched.

Cover

Rotary servo motor

Oil/water pool

Capillary action

Gear

Lubricating oil

Rotary servo motor

2 INSTALLATION 2.4 Protection from oil and water 17

18

2.6 Rotary servo motors with an oil seal For rotary servo motors with an oil seal, the oil seal prevents the entry of oil into the rotary servo motor. Make sure to install it

in accordance with this section.

Even if the oil seal on the rotary servo motor makes noises during operation, it does not indicate a problem with the functions.

Pressure and oil level Install the rotary servo motor horizontally, and set the oil level in the gear box to be always lower than the oil seal lip. If the oil

level is higher than the oil seal lip, the oil enters the rotary servo motor and may cause a malfunction. Refer to the chapter of

the rotary servo motor series for the height above oil level.

High pressure against the oil seal causes abrasion and shortens the service life of the product. Keep constant internal

pressure by equipping a ventilator to the gear box.

Temperature If the lip reaches a high temperature, the service life of the oil seal will be shortened. Maximum applicable temperature of

material of the oil lip is 100 C, and the temperature of the oil lip increases by 10 C to 15 C at maximum rotation. Keep high-

temperature oil away from the oil lip.

2.7 Inspection items To prevent a malfunction, do not perform an insulation resistance test (megger test) on the rotary servo motor.

Do not disassemble and/or repair the equipment on customer side.

Periodic inspection Perform the following inspections.

Check the bearings, brake section, and the like for unusual noise.

Check the cables and the like for scratches or cracks. Especially when the cables are movable, perform periodic

inspections according to operating conditions.

Check the rotary servo motor shaft and coupling for misalignment.

Check the power connector and encoder connector tightening screws for looseness.

Gear Shaft Rotary servo motor

Height above oil level

Lip

Oil seal

2 INSTALLATION 2.6 Rotary servo motors with an oil seal

2

2.8 Parts with a service life The service life of the following parts is listed below. If any fault is found in a part, replace it immediately because its service<