Yealink VC200 Quick Start Guide

Yealink VC200 Video Conferencing Endpoint Quick Start Guide V32.3 Applies to firmware version 80.32.0.3 or later

Yealink Network Technology CO., LTD

TV TV

We recommend that you use the accessories provided or approved by Yealink. The use of

unapproved third-party accessories may result in reduced performance.

Use the Yealink original PoE adapter (54V/0.56A) to charge the endpoint only. The use of the

third-party PoE adapter may cause the damage to the endpoint.

Before using the HDMI cable, put the magnet rings on it to prevent electromagnetic interference.

Endpoint Installation

Select one of the following installation method:

Put on a Flat Surface

You can put the endpoint on a conference room table.

Mount on top of a TV

You can mount endpoint on top of the TV when the thickness of the TV is between 1mm and

36mm.

The base of the camera must be parallel to the top of TV.

You can adjust the angle of the camera manually. The angle can be up to 30 degree.

Choose other installation method if your TV is more than 36 mm. 1

Package Contents

3m Ethernet CableAAA Battery2VC200 Codec

VCR11 Remote Control

1.8m HDMI Cable (for the display device)

Cable Tie5

Power Cord 2m Ethernet Cable (CAT5E FTP cable)

PSE

OK

Quick Start Guide

1/4-20 UNC Screw PoE Adapter

48mm 2

1

2

Hole depth: 30mm Hole diameter: 6mm

3

TV Stand

Mount on a Wall

You can purchase a bracket to mount your endpoint on a wall. The recommended height is

1.6m above the ground.

Mount onto a TV Stand or a Tripod

You need to purchase a TV stand or a tripod separately. The TV stand or a tripod should be able to bear a weight of at least 5kg.

1/4-20 UNC screw

1/4-20 UNC screw

T430 screws

Expansion bolts

3

PSE

VCH50

MINI DP HDMI

CodecAudio

Endpoint Connections

Display

1.8m HDMI Cable

3m Ethernet Cable

Choose one of the following: Wired network: using 2m Ethernet cable Wireless network: do not connect an Ethernet cable

You can choose wired sharing or wireless sharing method to share PC content. You need to

purchase the desired accessories.

Wired Sharing

VC Hub/Phone port on VC200 codec

7. 5m

Et

he rn

et C

ab le

1.2m HDMI Cable

1.2m Mini-DP Cable or

For more information on WPP20 wireless presentation pod, refer to Yealink WPP20 Wireless Presentation Pod Quick Start Guide.

PC

Wireless Sharing

WPP20 Wireless Presentation Pod

PC

Sharing Content

4

VCH50

MINI DP HDMI CodecAudio

PSE

VC Hub/Phone port on VC200 codec

7.

5m

Et he

rn et

C ab

le

2m

Et

he rn

et C

ab le

3m Ethernet Cable

CP960

CP960 Conference Phone Connections You can purchase CP960 conference phone separately, it can act as the audio input or output device.

If you do not need the VCH50 video conferencing hub to share content, You can connect PSE

of CP960 conference phone to the VC Hub/Phone port directly.

Remote Control and Cable Ties Installation

Network Environment

Bandwidth Requirements

Both downlink bandwidth and uplink bandwidth should meet above requirements.

The bandwidth mentioned above is based on a two-way call. Bandwidth in head office should be

increased along with the growing number of connected branch offices.

Network Deployment

Choose Cloud deployment or traditional deployment according to your need.

Cloud Deployment

Cloud deployment does not need complex network settings. you only need to get account

information from your system administrator, and log into the video conference platform.

Do the following to log into the video conference platform via remote control:

1. Select More->Setting->Advanced (Default Admin Password:0000)->Video Conference Platform.

2. In the Cloud Account field, check the Enabled checkbox.

Video Resolution Recommended Bandwidth

Full HD 1080P 1.3Mb

People 1080P+Content 1080P 2.6Mb

5

3. Select the desired platform from the pull-down list of Platform Type.

4. Configure the desired platform and log in.

Traditional Deployment

If you deploy endpoint in the head office, make sure it is reachable from public network.

If you deploy endpoint in the branch office, use intelligent traversal to deploy it or just follow the

same steps as for the head office.

Head Office

If you deploy endpoint in the head office, at least one static public IP address is required to allow

branch offices to connect.

Do one of the following to deploy endpoint:

Option1: Assign a static public IP address to your endpoint.

Option2: If you deploy endpoint in an Intranet (behind the firewall), assign a static private IP address

to it and do port mapping on the firewall.

Configure a Static IP

The following introduces how to use the remote control to configure a static IPv4 address:

1. Select More->Network->Wired Network (Default Admin Password:0000).

2. Select IPv4 from the pull-down list of IP Mode.

3. Select IPv4, and then press OK key.

4. Uncheck the DHCP checkbox.

5. Enter the IP address, subnet mask, gateway and DNS information in corresponding fields.

6. Save the change.

The screen prompts Reboot now?.

7. Select OK to reboot the endpoint.

Configure Port Mapping

If you deploy endpoint in an Intranet, you must forward the following ports to the public network on

the firewall, so that your endpoint can receive a public-to-private call.

Branch Office

If you deploy endpoint in the branch office, do one of the following to deploy it:

PortFunction

H.323 signal port

SIP optional

Audio & Video media stream port

Web management port optional

Protocol Type

UDP/TCP

5060-5061

443

50000-51000

1719-1720

TCP/UDP

TCP/UDP

TCP

6

Option1: Deploy the endpoint following the same steps as for the head office. In this way,

both inbound and outbound calls are available.

Option2: Deploy the endpoint using intelligent traversal. You only need to assign a private IP

address to your endpoint. Make sure this private IP address can access the public network.

Only outbound calls are available when using this method.

When you use intelligent traversal to deploy your endpoint, you have to open following ports on

your firewall if they are restricted.

It is recommended that you forward the web management port(443/TCP) to the public network, so

that the head office can remotely manage the branch office.

Troubleshooting

Connectivity Testing

After installation and deployment, you can test the endpoint by dialing the Yealink Demo Room

(117.28.251.50 or 117.28.234.45 ). If you cant dial out successfully, please contact your IT administrator

to check the network.

Configuring Static NAT

If you do not use Cloud platform and deploy your endpoint in an Intranet, you have configured port

mapping on the firewall or gateway, but you find that local endpoint appears black screen and you

cannot hear sound when you call Yealink Demo or other endpoints. The most likely reason is that the

firewall or gateway in your environment does not support the ALG feature. In this situation, please take

the following actions so that the static NAT feature on the endpoint can solve this problem.

To configure static NAT via the remote control:

1. Select More->Network->Wired Network (Default Admin Password:0000)->NAT/Firewall.

2. Select Auto from the pull-down list of Type, the endpoint will obtain public IP address automatically.

3. If the endpoint does not obtain a public IP address automatically, select Manual Settings from the

pull-down list of Type, and then enter the public IP address in the Public IP Address field.

4. Save the change.

PortFunction

H.323 signal port

SIP optional

Audio & Video media stream port

Protocol Type

UDP/TCP

TCP/UDP

TCP/UDP

50000-51000

5060-5061

1719-1720

YEALINK(XIAMEN) NETWORK TECHNOLOGY CO.,LTD. Web: www.yealink.com | Addr: 309, 3th Floor, No.16, Yun Ding North Road, Huli District, Xiamen City, Fujian, P.R. China Copyright2018YEALINK(XIAMEN) NETWORK TECHNOLOGY CO.,LTD. All rights reserved.

About Yealink Yealink (Stock Code: 300628) is a global leading unified communication (UC) terminal solution provider that primarily offers video conferencing systems and voice communication solutions. Founded in 2001, Yealink leverages its independent research and development and innovation to pursue its core mission: Easy collaboration, high productivity. The companys high-quality UC terminal solutions enhance the work efficiency and competitiv