Contents

This owners manual applies to the APV series.
FOREWORD
- All information in this manual is based on the latest product information available at the time of publication. Due to improvements or other changes, there may be discrepancies between information in this manual and your vehicle. PT. SUZUKI MOTOR COR...
- This vehicle may not comply with standards or regulations of other countries. Before attempting to register this vehicle in any other country, check all applicable regulations and make any necessary modifications.
IMPORTANT
- WARNING/CAUTION/NOTE
MODIFICATION WARNING
INTRODUCTION
SERVICE STATION GUIDE
TABLE OF CONTENTS
BEFORE DRIVING
Fuel Recommendation
- Petrol/Ethanol blends
- Petrol/Methanol blends
Keys
- Immobilizer System (if equipped)
- Ignition Key Reminder (if equipped)
Door Locks
- Side Door Locks
- Central Door Locking System (if equipped)
- Keyless Entry System (if equipped)
  - Replacement of the transmitter battery
- Rearend Door Lock
Windows
- Manual Window Control (if equipped)
- Electric Window Controls (if equipped)
Mirrors
- Inside Rearview Mirror
- Outside Rearview Mirrors
- Electric Mirrors (if equipped)
Seat Adjustment
- Adjusting Seat Position (if equipped)
- Adjusting Seatbacks
- Entry to/Exit from the 3rd Row Seat (if equipped) (except for rigid seat)
Adjustable Head Restraints (if equipped)
Seat Belts and Child Restraint Systems
- Lap-Shoulder Belt (if equipped)
  - Safety reminder
- Lap Belt (if equipped)
- Shoulder Anchor Height Adjuster (if equipped)
- Seat Belt Inspection
- Child Restraint Systems
  - Installation with lap-shoulder seat belts
  - Installation with a lap belt
- Seat Belt Pretensioner System (if equipped)
Supplemental Restraint System (air bags) (if equipped)
- Air bag symbol (if equipped) meaning
- Air bag symbol
- Servicing the air bag system
STEERING COLUMN CONTROLS
- Ignition Switch
- Lighting/Turn Signal Control Lever
- Windscreen Wiper and Washer Lever
- Rear Window Wiper/Washer Switch (if equipped)
- Tilt Steering Lock Lever (if equipped)
  - 1) Push down on the lock lever to unlock the steering column.
  - 2) Adjust the steering wheel to the desired height and lock the steering column by pulling the lock lever fully up.
  - 3) Try moving the steering wheel up and down to make sure it is securely locked in position.
- Horn
MEMO
INSTRUMENT PANEL
- Instrument Panel
  - 1. Side ventilator
  - 2. Centre ventilator
  - 3. Hazard warning switch
  - 4. Audio ON/OFF button
  - 5. Windscreen wiper and washer switch/ Rear window wiper and washer switch (if equipped)
  - 6. Instrument cluster
  - 7. Lighting switch/Turn signal and dimmer switch
  - 8. Glove box
  - 9. Air flow selector (if equipped)
  - 10. Ashtray
  - 11. Blower speed selector (if equipped)
  - 12. Temperature selector (if equipped)
  - 13. Cigarette lighter (if equipped)
  - 14. Fuse box
  - 15. Air bag (if equipped)
  - 16. Ignition switch
  - 17. Bonnet release
  - 18. Other switches (if equipped)
- Instrument Cluster
  - 1. Tachometer (if equipped)
  - 2. Temperature gauge
  - 3. Fuel gauge
  - 4. Speedometer
  - 5. Warning and indicator lights
  - 6. A/T selector position indicator (if equipped)
  - 7. Odometer/Trip meter
  - 8. Odometer/Trip meter selector knob
  - with tachometer
  - without tachometer
- Warning and Indicator Lights
  - 1) Pull off the road and stop carefully.
  - 2) Test the brakes by carefully starting and stopping at the side of the road.
  - 1) Pull off the road and stop carefully.
  - 2) Turn the ignition switch to LOCK and then start the engine again.
  - 3) If the warning light comes on briefly then turns off, the system is normal. If the warning light still stays on, the system will be something wrong.
- A/T Selector Position Indicator (if equipped)
- Speedometer/Odometer/Trip meter
- Tachometer (if equipped)
- Fuel Gauge
- Temperature Gauge
- Hazard Warning Switch
- Heated Rear Window Switch (if equipped)
- Headlight Leveling Switch (if equipped)
- Fog Light Switch (if equipped)
- Cigarette Lighter and Ashtray
  - Rear (if equipped)
- Clock (if equipped)
- Glove Box
- Heating System
  - Front (if equipped)
    - 1. Windscreen demister outlet
    - 2. Side demister outlet
    - 3. Side outlet
    - 4. Centre outlet
    - 5. Floor outlet
  - Rear (if equipped)
    - 6. Overhead outlet
  - Front
  - Ventilation (a)
  - Bi-level (b)
  - Heat (c)
  - Heat & demist (d) (if equipped)
  - Demist (e) (if equipped)
  - Blower speed selector (2)
  - Temperature selector (3)
- Air Conditioning System (if equipped)
  - Rear blower switch
OTHER CONTROLS AND EQUIPMENT
Parking Brake Lever
- (1) To apply
- (2) To release
- (3) To release
- 1) Apply the parking brake.
- 2) Shift the manual transmission into reverse or first gear, or the automatic transmission into P (Park).
- 3) With the engine off, get out of the vehicle and put chocks under the wheels.
- 4) Release the parking brake. When you return to your vehicle, you must remember to first apply the parking brake, then remove the wheel chocks.
Pedal
Gear Lever
Fuel Filler Cap
- 1) Open the fuel filler door by inserting the key and turning it clockwise or by pulling up the opener lever on the outboard side of the drivers seat (if equipped).
- 2) Remove the cap by turning it counterclockwise.
- 1) Turn the cap clockwise until you hear several clicks.
- 2) Close the fuel filler door. Turn the key counterclockwise to lock the door or by simply push the door firmly.
Folding Seats
- 1) Lower the adjustable head restraint (if equipped) fully.
- 2) Return the armrest (if equipped) to the stowed position.
- 3) Pull up the lever (1) on outboard side of the 3rd row seat or pushing the lever (2) on the rear of the 3rd row seat. The seatback will fold forward.
- 4) Fold the entire seat forward.
- 5) Hook the strap on the rear of the 3rd row seat to the 2nd row seat head restraint as shown in the illustration.
- 1) Unhook the strap and stow it into the pocket at the 3rd row seat cushion.
- 2) Raise the entire seat and then raise the seatback to an upright position.
Seat Armrest (if equipped)
Sun Visor
Interior Light Switch
- (1) The light comes on and stays on regardless of whether the door is open or closed.
- (2) The light comes on when the door is opened.
- (3) The light remains off even when the door is opened.
Assist Grips (if equipped)
Frame Hooks
Bonnet
- 1) Pull the bonnet release handle located on the drivers outboard side of the instrument panel. This will disengage the bonnet lock halfway.
- 2) Push the under-bonnet release lever up with your finger, as shown in the illustration. While pushing the lever, lift up the bonnet.
- 3) Continue to lift up the bonnet until it is high enough to support with the prop rod.
- 1) Lift the bonnet up slightly and remove the prop rod from the hole. Put the prop rod back to the holding clip.
- 2) Lower the bonnet to about 20 cm above the bumper, then let it drop down. Make sure the bonnet is securely latched after closing.
Bottle Holder (if equipped)
Engine Compartment
- 1) Adjust the front seatback to the fairly upright position.
- 2) Slide the front seat to the rearmost position.
- 3) Unhook the two lock handles on the front end of the seat.
- 4) Raise the seat slowly.
- 5)
Tyre Changing Tool
- 1) Loosen the spare tyre holder hook bolt.
- 2) Unhook the spare tyre holder and lower it slowly.
- 3) Remove the tyre.
Radio Antenna (if equipped)
OPERATING YOUR VEHICLE
Exhaust Gas Warning
Daily Inspection Checklist
- 1) Make sure that windows, mirrors, lights, and reflectors are clean and unobstructed.
- 2) Visually check the tyres for the following points:
- 3) Look for fluid and oil leaks.
- 4) Make sure the bonnet is fully closed and latched.
- 5) Check the headlights, turn signal lights, brake lights and horn for proper operation.
- 6) Adjust the seat and head restraint (if adjustable).
- 7) Check the brake pedal and the parking brake lever.
- 8) Adjust the mirrors.
- 9) Make sure that you and all passengers have properly fastened your seat belts.
- 10) Make sure that all warning lights come on as the key is turned to the ON or START position.
- 11) Check all gauges.
- 12) Make sure that the BRAKE FLUID LEVEL WARNING light and the PARKING BRAKE INDICATOR light (if equipped) are off after the parking brake is released.
- 1) Engine oil level
- 2) Coolant level
- 3) Brake fluid level
- 4) Power steering (if equipped) fluid level
- 5) Windscreen washer fluid level
- 6) Battery solution level
- 7) Bonnet latch operation Pull the bonnet release handle inside the vehicle. Make sure that you cannot open the bonnet all the way without releasing the secondary latch. Be sure to close the bonnet securely after checking for proper latch operation. ...
Engine Oil Consumption
Starting the Engine
- 1) Make sure the parking brake is applied fully.
- 2) Manual transmission Change into N (Neutral) and depress the clutch pedal all the way to the floor. Hold it while starting the engine. Automatic transmission If the gear lever is not in P (Park) position, change into P (Pa...
Using the Transmission
- (1) Overdrive off switch
Braking
- (1) ABS warning light
- (2) Brake system warning light
- 1) Pull off the road and stop carefully.
- 2) Turn the ignition switch to LOCK and then start the engine again.
Running-In
Catalytic Converter (if equipped)
Improving Fuel Economy
DRIVING TIPS
- High-Speed Driving
- Driving on Hills
- Driving on Slippery Roads
  - 1) Change back and forth between a forward range (or first gear for manual transmission) and reverse. This will create a rocking motion which may give you enough momentum to free the vehicle. Press gently on the accelerator to keep wheel spin to a mi...
  - 2) If your vehicle remains stuck after a few minutes of rocking, get another vehicle to pull you out.
VEHICLE LOADING AND TOWING
- Vehicle Loading
- Trailer Towing
- Towing Your Vehicle (recreational towing)
  - To tow a vehicle with the rear wheels secured to a towing dolly:
    - 1) Turn the ignition key to the ACC position to stop the engine and to unlocked the steering wheel.
    - 2) Make sure the front wheels are facing straight forward and secure the steering wheel with a steering wheel clamping device designed for towing service.
INSPECTION AND MAINTENANCE
Maintenance Schedule
Periodic Maintenance Schedule
- (1) V-rib belt
Maintenance Recommended under Severe Driving Conditions
Drive Belt
Engine Oil and Filter
- (1) Preferred
- 1) Remove the oil filler cap.
- 2) Place a drain pan under the drain plug (1).
- 3) Using a wrench, remove the drain plug and drain out the engine oil.
- 4) Reinstall the drain plug and gasket. Tighten the plug with a wrench to the specified torque.
- 1) Using an oil filter wrench, turn the oil filter counterclockwise and remove it.
- 2) Using a clean rag, wipe off the mounting surface on the engine where the new filter will be seated.
- 3) Smear a little engine oil around the rubber gasket of the new oil filter.
- 4) Screw on the new filter by hand until the filter gasket contacts the mounting surface.
  - (1) Oil filter
  - (2) 3/4 turn
- 5) Tighten the filter specified turn from the point of contact with the mounting surface (or to the specified torque) using an oil filter wrench.
- 1) Pour oil through the filler hole and install the filler cap. For the approximate capacity of the oil, refer to the CAPACITIES item in the SPECIFICATIONS section.
- 2) Start the engine and look carefully for leaks at the oil filter and drain plug. Run the engine at various speeds for at least 5 minutes.
- 3) Stop the engine and wait about 5 minutes. Check the oil level again and add oil if necessary. Check for leaks again.
Gear Oil
- (1) Oil filler and level plug
- (2) Oil drain plug
- (1) Oil filler/level plug
- (2) Oil drain plug
- 1) Park the vehicle on a level surface with the parking brake applied. Then, stop the engine.
- 2) Remove the oil filler plug (1).
- 3) Feel the inside of the hole with your finger. If the oil level comes up to the bottom of the plug hole, the oil level is correct. If so, reinstall the plug.
- 4) If the oil level is low, add gear oil through the oil filler plug hole (1) until the oil level reaches the bottom of the filler hole, then reinstall the plug.
- 1) Remove the oil filler plug (1).
- 2) Remove the drain plug (2), drain the oil, and reinstall the drain plug.
- 3) Pour new gear oil of the specified type through the filler hole (1) until the oil level reaches the bottom of the filler hole.
- 4) Reinstall the filler plug.
Automatic Transmission (AT) Fluid
- 1) To warm up the transmission fluid, drive the vehicle or idle the engine until the temperature gauge indicates normal operating temperature.
- 2) Then drive for ten more minutes.
- 3) Park your vehicle on level ground.
- 4) Apply the parking brake and then start the engine in P (Park). Let it idle for two minutes and keep it running during the fluid level check.
- 5) With your foot on the brake pedal, move the selector lever through each range, pausing for about three seconds in each range. Then move it back to the P (Park) position.
- 6) The handle of the A/T fluid dipstick is colored red for easy identification. Remove the dipstick, clean it and push it back in until the cap seats. Then pull out the dipstick.
- 7) Check both sides of the dipstick, and read the lowest level. The fluid level should be between the two marks in the HOT range on the dipstick.
  - (1) FULL HOT
  - (2) LOW HOT
  - (3) The lowest point = Fluid level
- 8) Add just enough specified fluid through the dipstick hole to fill the transmission to the proper level.
Engine Coolant
- (1) Trapped air
Windscreen Washer Fluid
Air Cleaner
- 1) Loosen the clamp of the hose and detach the hose from the cover.
- 2) Remove the intake air temperature coupler (1).
- 3) Unclamp the side clamps.
- 4) With the far side of the cleaner cover lifted, move the cover to the near side to remove it.
- 5) Remove the element from the air cleaner case.
- 6) This air cleaner element is of dry type. Remember that it needs cleaning according to the following method.
- 7) Blow off dust on cleaner element by compressed air from inside the element, or replace the element as necessary.
Spark Plugs
- 1) Remove the ignitor cover.
- 2) Disconnect the coupler while pushing the release lever.
- 3) Remove the ignitor bolts.
- 4) Pull the spark plug boots out.
Brakes
Steering
Power Steering (if equipped)
- (1) UPPER
- (2) LOWER
Clutch Pedal
Tyres
- 1) Measure the air pressure with a tyre gauge. Adjust the pressure if necessary. Remember to check the spare tyre, too.
  - (1) Tread wear indicator
  - (2) Indicator location mark
- 2) Check that the depth of the tread groove is more than 1.6 mm (0.06 in.). To help you check this, the tyres have molded-in tread wear indicators in the grooves. When the indicators appear on the tread surface, the remaining depth of the tread is 1....
- 3) Check for abnormal wear, cracks and damage. Any tyres with cracks or other damage should be replaced. If any tyres show abnormal wear, have them inspected by your SUZUKI dealer.
- 4) Check for loose wheel nuts.
- 5) Check that there are no nails, stones or other objects sticking into the tyres.
- 1) Remove the jack, tools and spare wheel from the vehicle. To remove the spare wheel under the rear floor, loosen the support bolt (1), unhook the tyre holder (2) and lower it slowly.
- 2) Loosen, but do not remove the wheel nuts.
- 3) Jack up the vehicle (follow the jacking instructions in the EMERGENCY SERVICE section in this manual).
- 4) Remove the wheel nuts and wheel.
- 5) Before installing the new wheel, clean any mud or dirt off from the surface of the wheel and hub with a clean cloth. Clean the hub carefully; it may be hotfrom driving.
- 6) Install the new wheel and replace the wheel nuts with their cone shaped end facing the wheel. Tighten each nut snugly by hand until the wheel is securely seated on the hub.
- 7) Lower the jack and fully tighten the nuts to the specified torque in a crisscross fashion with a wrench as shown in the illustration.
Battery
Fuses
Bulb Replacement
- (1) Removal
- (2) Installation
- (3) Removal
- (4) Installation
Wiper Blades
- 1) Hold the wiper arm away from the window.
- 2) Squeeze lock (1) towards wiper arm (2) and remove the wiper frame from the arm as shown.
- 3) Unlock the lock end of the wiper blade and slide the blade out as shown.
  - (1) Locked end
  - (1) Retainer
- 4) If the new blade is provided without the two metal retainers, move them from the old blade to the new one.
- 5) Install the new blade in the reverse order of removal, with the locked end positioned toward the wiper arm. Make sure the blade is properly retained by all the hooks. Lock the blade end into place.
- 6) Reinstall wiper frame to arm, making sure that the lock lever is snapped securely into the arm.
Air Conditioning System
MEMO
EMERGENCY SERVICE
Jacking Instructions
- 1) Place the vehicle on level, hard ground.
- 2) Apply the parking brake firmly and select P (Park) if your vehicle has an automatic transmission, or change into R (Reverse) if your vehicle has a manual transmission. Chock the front and rear of the wheel diagonally opposite of the wh...
- 3) Turn on the hazard warning flasher if your vehicle is near traffic.
- 4) Position the jack vertically and raise the jack by turning the jack handle clockwise until the jack head recess fits the jacking point.
- 5) Continue to raise the jack slowly and smoothly until the tyre clears the ground. Do not raise the vehicle more than necessary.
Jump Starting Instructions
- 1) Use only a 12 volt battery to jump start your vehicle. Position the good 12 V battery close to your vehicle so that the jump leads will reach both batteries. When using a battery installed on another vehicle, DO NOT LET THE VEHICLES TOUCH. Apply t...
- 2) Turn off all vehicle accessories, except those necessary for safety reasons (for example, headlights or hazard lights).
- 3) Make jump lead connections as follows:
  - 1. Connect one end of the first jump lead to the positive (+) terminal of the flat battery (1).
  - 2. Connect the other end to the positive (+) terminal of the booster battery (2).
  - 3. Connect one end of the second jump lead to the negative () terminal of the booster battery (2).
  - 4. Make the final connection to an unpainted, heavy metal part (i.e. engine hook (3)) of the engine of the vehicle with the flat battery (1).
- 4) If the booster battery you are using is fitted to another vehicle, start the engine of the vehicle with the booster battery. Run the engine at moderate speed.
- 5) Start the engine of the vehicle with the flat battery.
- 6) Remove the jump leads in the exact reverse order in which you connected them.
Towing
Emergency Remedies
- 1) Try turning the ignition switch to the START position with the headlights turned on to determine the battery condition. If the headlights go excessively dim or go off, it usually means that either the battery is flat or the battery terminal ...
- 2) If the headlights remain bright, check the fuses. If the reason for failure of the starter is not obvious, there may be a major electrical problem. Have the vehicle inspected by your authorized SUZUKI dealer.
- 1) Turn off the air conditioner, if equipped.
- 2) Take the vehicle to a safe place and park.
- 3) Let the engine run at normal idle speed for a few minutes until the indicator is within the normal, acceptable temperature range between H and C.
- 1) Turn off the engine and check that the water pump belt and pulleys are not damaged or slipping. If any abnormality is found, correct it.
- 2) Check the coolant level in the reservoir. If it is found to be lower than the LOW line, look for leaks at the radiator, water pump, and radiator and heater hoses. If you locate any leaks that may have caused the overheating, do not run the e...
- 3) If you do not find a leak, carefully add coolant to the reservoir and then the radiator, if necessary. (Refer to Engine Coolant in the INSPECTION AND MAINTENANCE section.)
BODY WORK CARE
- Corrosion Prevention
  - 1) Accumulation of road salt, dirt, moisture, or chemicals in hard to reach areas of the vehicle underbody or frame.
  - 2) Chipping, scratches and any damage to treated or painted metal surfaces resulting from minor accidents or abrasion by stones and gravel.
  - 1) Road salt, dust control chemicals, sea air or industrial pollution will all accelerate the corrosion of metal.
  - 2) High humidity will increase the rate of corrosion particularly when the temperature range is just above the freezing point.
  - 3) Moisture in certain areas of a vehicle for an extended period of time may promote corrosion even though other body sections may be completely dry.
  - 4) High temperatures will cause an accelerated rate of corrosion to parts of the vehicle which are not well ventilated to permit quick drying.
- Vehicle Cleaning
  - 1) Flush the underside of body and wheel housings with pressurized water to remove mud and debris. Use plenty of water.
  - 2) Rinse the body to loosen the dirt. Remove dirt and mud from the body exterior with running water. You may use a soft sponge or brush. Do not use hard materials which can scratch the paint or plastic. Remember that the headlight covers or lenses ar...
  - 3) Wash the entire exterior with a mild detergent or car wash soap using a sponge or soft cloth. The sponge or cloth should be frequently soaked in the soap solution.
  - 4) Once the dirt has been completely removed, rinse off the detergent with running water.
  - 5) After rinsing, wipe off the vehicle body with a wet chamois or cloth and allow it to dry in the shade.
  - 6) Check carefully for damage to painted surfaces. If there is any damage, touch-up the damage following the procedure below:
    - 1. Clean all damaged spots and allow them to dry.
    - 2. Stir the paint and touch-up the damaged spots lightly using a small brush.
    - 3. Allow the paint to dry completely.
MEMO
GENERAL INFORMATION
- Vehicle Identification
  - (1) Stamping position of the chassis serial number
SUPPLEMENT
- 1. For Australia
- 2. For Saudi Arabia (GCC) Specification Vehicle
  - Manual transmission vehicles
  - Automatic transmission vehicles
  - Max power : 68.0 kw/5750 rpm
  - Max torque : 127 Nm/4500 rpm
  - Max speed : 145 km/h (M/T) 140 km/h (A/T)
MEMO

Suzuki APV 2020 Owner's Manual

Pages 160

Year 2020

Language(s)

of 160

Suzuki APV 2020 Car Specification

The Suzuki APV 2020 is a versatile multi-purpose vehicle designed to accommodate both family and business needs with practicality and efficiency. It is powered by a robust 1.5-liter inline-four engine, generating a maximum power output of approximately 94 horsepower and 126 Nm of torque, paired with a 5-speed manual transmission or a 4-speed automatic transmission. The vehicle offers a spacious interior with a seating capacity for up to eight passengers, featuring flexible seating arrangements to optimize cargo space as needed.

The exterior dimensions include a length of 4,155 mm, a width of 1,655 mm, and a height of 1,865 mm, with a wheelbase of 2,625 mm, ensuring a compact yet roomy design suitable for urban and suburban environments. The APV 2020 is equipped with McPherson strut front suspension and a rigid axle with leaf spring rear suspension, providing a comfortable ride while maintaining strong load-carrying capability.

Safety features in the Suzuki APV 2020 include dual front airbags, an anti-lock braking system (ABS), and electronic brakeforce distribution (EBD), contributing to enhanced occupant protection and vehicle stability. The vehicle also incorporates convenience features such as power steering, air conditioning, and an audio system with CD and MP3 playback options.

With its combination of reliability, efficiency, and practicality, the Suzuki APV 2020 addresses the diverse needs of its users, making it a suitable choice for those seeking a reliable multi-purpose vehicle. Its design emphasizes ease of use and maintenance, appealing to families and businesses alike looking for a cost-effective transportation solution.

Suzuki APV 2020 Car F.A.Q.

How do I reset the maintenance light on a Suzuki APV 2020?

To reset the maintenance light on your Suzuki APV 2020, turn the ignition switch to the "ON" position. Press the trip meter reset button until the maintenance light begins to flash. After a few seconds, the light should reset.

What type of engine oil is recommended for the Suzuki APV 2020?

For the Suzuki APV 2020, it is recommended to use 10W-40 or 5W-30 engine oil, depending on the climate and usage conditions. Always refer to the owner's manual for the most accurate information.

How can I improve the fuel efficiency of my Suzuki APV 2020?

To improve the fuel efficiency of your Suzuki APV 2020, ensure regular maintenance such as air filter replacement, proper tire inflation, and using the recommended grade of engine oil. Additionally, avoid rapid acceleration and excessive idling.

What is the recommended tire pressure for the Suzuki APV 2020?

The recommended tire pressure for the Suzuki APV 2020 is typically 32 psi for both front and rear tires. However, it's important to check the sticker on the driver's side door jamb or the owner's manual for specific recommendations.

How do I replace the air filter in a Suzuki APV 2020?

To replace the air filter in your Suzuki APV 2020, locate the air filter box in the engine compartment. Release the clips or screws, remove the old filter, and insert the new one. Ensure it is seated properly before securing the air filter box.

What should I do if my Suzuki APV 2020 won't start?

If your Suzuki APV 2020 won't start, check the battery connections for corrosion or looseness, ensure the fuel level is adequate, and inspect the fuses. If the issue persists, it may be necessary to consult a professional mechanic.

How often should I change the brake fluid in my Suzuki APV 2020?

It is recommended to change the brake fluid in your Suzuki APV 2020 every 2 years or 30,000 kilometers, whichever comes first. Always refer to the owner's manual for specific intervals.

What are the common causes of overheating in a Suzuki APV 2020?

Common causes of overheating in a Suzuki APV 2020 include low coolant levels, a faulty thermostat, a clogged radiator, or a malfunctioning water pump. Regular maintenance can help prevent these issues.

How do I check the transmission fluid level in a Suzuki APV 2020?

To check the transmission fluid level in a Suzuki APV 2020, warm up the engine, park on a level surface, and locate the transmission dipstick. Pull it out, wipe it clean, reinsert it, and check the fluid level, ensuring it is within the recommended range.

What are the recommended maintenance intervals for a Suzuki APV 2020?

The recommended maintenance intervals for a Suzuki APV 2020 are typically every 10,000 kilometers or 6 months, whichever comes first. This includes oil changes, air filter replacements, and brake inspections. Always refer to the owner's manual for detailed schedules.