Horizon Fitness T101-06 Owner's Manual V2

Read the TREADMILL GUIDE before using this OWNERS MANUAL.

T101

OWNERS MANUAL

HZ19_T101-5_OM_r1_0_D.indd 1 3/21/19 10:19 AM

3

IMPORTANT PRECAUTIONS SAVE THESE INSTRUCTIONS When using an electrical product, basic precautions should always be followed, including the following: Read all instructions before using this treadmill. It is the responsibility of the owner to ensure that all users of this treadmill are adequately informed of all warnings and precautions. If you have any questions after reading this guide, contact Customer Tech Support at the number listed on the back panel of the OWNERS MANUAL.

This treadmill is intended for in-home use only. Do not use this treadmill in any commercial, rental, school or institutional setting. Failure to comply will void the warranty.

EN G

LI SH

HZ19_T101-5_OM_r1_0_D.indd 2-3 3/21/19 10:19 AM

54

TO REDUCE THE RISK OF BURNS, FIRE, ELECTRICAL SHOCK OR INJURY TO PERSONS: At NO time should pets or children under the age of 13 be closer to the treadmill than 10 feet. At NO time should children under the age of 13 use the treadmill. Children over the age of 13 or disabled persons should not use the treadmill without adult supervision. Use the treadmill only for its intended use as described in the treadmill guide and owners manual. Do not use other attachments that are not recommended by the manufacturer. Attachments may cause injury. Never operate the treadmill if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged,

or immersed in water. Return the treadmill to a service center for examination and repair. Keep power cord away from heated surfaces. Do not carry this unit by its supply cord or use the cord as a handle. Never operate the treadmill with the air opening blocked. Keep the air opening clean, free of lint, hair, and the like. To prevent electrical shock, never drop or insert any object into any opening. Do not operate where aerosol (spray) products are being used or when oxygen is being administered. To disconnect, turn all controls to the off position, then remove plug from outlet. Do not use treadmill in any location that is not temperature controlled, such as but not limited to garages, porches, pool rooms,

bathrooms, car ports or outdoors. Failure to comply will void the warranty. This treadmill is intended for in-home use only. Do not use this treadmill in any commercial, rental, school or institutional setting.

Failure to comply will void the warranty. Do not remove the console covers unless instructed by Customer Tech Support. Service should only be done by an authorized

service technician.

It is essential that your treadmill is used only indoors, in a climate controlled room. If your treadmill has been exposed to colder temperatures or high moisture climates, it is strongly recommended that the treadmill is warmed up to room temperature before first time use. Failure to do so may cause premature electronic failure.

TO REDUCE THE RISK OF BURNS, FIRE, ELECTRICAL SHOCK OR INJURY TO PERSONS: Never use the treadmill before securing the safety tether clip to your clothing. If you experience any kind of pain, including but not limited to chest pains, nausea, dizziness, or shortness of breath, stop

exercising immediately and consult your physician before continuing. When exercising, always maintain a comfortable pace. Do not wear clothes that might catch on any part of the treadmill. Always wear athletic shoes while using this equipment. Do not jump on the treadmill. At no time should more than one person be on treadmill while in operation. This treadmill should not be used by persons weighing more than specified in the OWNERS MANUAL WARRANTY SECTION. Failure

to comply will void the warranty. When lowering the treadmill deck, wait until rear feet are firmly on the floor before stepping on the deck. Disconnect all power before servicing or moving the equipment. To clean, wipe surfaces down with soap and slightly damp

cloth only; never use solvents. (See MAINTENANCE) The treadmill should never be left unattended when plugged in. Unplug from outlet when not in use, and before putting on

or taking off parts. Do not operate under blanket or pillow. Excessive heating can occur and cause fire, electric shock, or injury to persons. Connect this exercise product to a properly grounded outlet only.

WARNING

TO REDUCE THE RISK OF ELECTRICAL SHOCK: Always unplug the treadmill from the electrical outlet immediately after using, before cleaning, performing maintenance and putting on or taking off parts.

DANGER WARNING

EN G

LI SH

EN G

LISH

HZ19_T101-5_OM_r1_0_D.indd 4-5 3/21/19 10:19 AM

76

ASSEMBLY

There are several areas during the assembly process that special attention must be paid. It is very important to follow the assembly instructions correctly and to make sure all parts are firmly tightened. If the assembly instructions are not followed correctly, the treadmill could have parts that are not tightened and will seem loose and may cause irritating noises. To prevent damage to the treadmill, the assembly instructions must be reviewed and corrective actions should be taken.

Before proceeding, find your treadmills serial number located on a white barcode sticker near the on/off power switch and power cord and enter it in the space provided below.

ENTER YOUR SERIAL NUMBER AND MODEL NAME IN THE BOXES BELOW:

Refer to the SERIAL NUMBER and MODEL NAME when calling for service.

SERIAL NUMBER:

TM

WARNING

SERIAL NUMBER LOCATION

GROUNDING INSTRUCTIONS This product must be grounded. If a treadmill should malfunction or breakdown, grounding provides a path of least resistance for electrical current to reduce the risk of electrical shock. This product is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with local codes and ordinances.

Connect this exercise product to a properly grounded outlet only.

Never operate product with a damaged cord or plug even if it is working properly. Never operate any product if it appears damaged, or has been immersed in water. Contact Customer Tech Support for replacement or repair.

WARNING

DANGER Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service provider if you are in doubt as to whether the product is properly grounded. Do not modify the plug provided with the product. If it will not fit the outlet, have a proper outlet installed by a qualified electrician.

This product is for use on a nominal local voltage circuit and has a grounding plug. No adapter should be used with this product.

This product must be used on a dedicated circuit. To determine if you are on a dedicated circuit, shut off the power to that circuit and observe if any other devices lose power. If so, move devices to a different circuit. Note: There are usually multiple outlets on one circuit.

MODEL NAME: HORIZON TREADMILL

EN G

LISH EN

G LI

SH

HZ19_T101-5_OM_r1_0_D.indd 6-7 3/21/19 10:19 AM

98

SPEAKERS

WATER BOTTLE HOLDER

GRIP PULSE HANDRAILS

CONSOLE FAN

ON/OFF SWITCH

TRANSPORT WHEEL

POWER CORD

TABLET/READING RACK

CONSOLE

CONTROL PANEL AND DISPLAY WINDOWS

SAFETY KEY PLACEMENT

MOTOR COVER

RUNNING BELT/RUNNING DECK

SIDE RAIL

ROLLER END CAP

REAR ROLLER TENSION/ALIGNMENT BOLTS

CONSOLE MAST

FOOT LOCK LATCH (UNDERNEATH DECK)

FOOT LOCK LATCH DECAL (UNDERNEATH FOOT LATCH)

WATER BOTTLE HOLDER

KEEP HANDS AND FEET AWAY FROM THIS AREA.

HIGH-PRESSURE SHOCKS COULD

CAUSE BODILY INJURY.

CAUTION GARDEZ VOS MAINS ET VOS

PIEDS LCART DE CET ENDROIT. DES COUPS HAUTE PRESSION

PEUVENT CAUSER DES BLESSURES CORPORELLES.

ATTENTION MANTENGA LAS MANOS

Y LOS PIES ALEJADOS DE ESTA REA. DESCARGAS

DE ALTA PRESIN PODRAN OCASIONAR

LESIONES FSICAS.

PRECAUCIN

TOOLS INCLUDED:

F6 mm T-Wrench F5 mm L-Wrench F4 mm T-Wrench FPhillips Screwdriver

PARTS INCLUDED:

F1 Console Assembly F2 Console Masts F1 Hardware Kit F1 Safety Key F1 Audio Adapter Cable F 1 Bottle of Silicone Lubricant (for 2 applications) F2 Console Mast Covers F1 Power Cord

DO NOT ATTEMPT TO LIFT THE TREADMILL! Do not move or lift treadmill from packaging until specified to do so in the assembly instructions. You may remove the plastic wrap from console masts.

WARNING

UNPACKING Place the treadmill carton on a level flat surface. It is recommended that you place a protective covering on your floor. Take CAUTION when handling and transporting this unit. Never open box when it is on its side. Once the banding straps have been removed, do not lift or transport this unit unless it is fully assembled and in the upright folded position, with the lock latch secure. Unpack and assemble the unit where it will be used. The enclosed treadmill is equipped with high-pressure shocks and may spring open if mishandled. Never grab hold of any portion of the incline frame and attempt to lift or move the treadmill.

FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN INJURY!

WARNING

NOTE: During each assembly step, ensure that ALL nuts and bolts are in place and partially threaded in before completely tightening any ONE bolt.

NOTE: A light application of grease may aid in the installation of hardware. Any grease, such as lithium bike grease is recommended.

PRE ASSEMBLY

EN G

LI SH

EN G

LISH

NEED HELP?

If you have questions or if there are any missing parts,

contact Customer Tech Support.

HZ19_T101-5_OM_r1_0_D.indd 8-9 3/21/19 10:19 AM

1110

ASSEMBLY STEP 2ASSEMBLY STEP 1 A Cut the yellow banding straps and lift the running

deck upward from the rear to remove all contents from underneath the running deck.

B Open HARDWARE FOR STEP 1.

C Attach CONSOLE MAST BRACKETS (B) to the CONSOLE MASTS (1 & 2) using 8 BOLTS (A).

A Open HARDWARE FOR STEP 2.

B With the RUNNING DECK in the raised position, attach the LEFT CONSOLE MAST (1) to the BASE FRAME (2) using 4 BOLTS (A), 4 SPRING WASHERS (B) and 4 FLAT WASHERS (C).

HARDWARE FOR STEP 1 PART TYPE DESCRIPTION QTY

M6X1.0PX10L 8A BOLT

A

1

2

NOTE: Do not fully tighten bolts until STEP 5.

NOTE: Do not fully tighten bolts until STEP 5.

1

B

A B

C

HARDWARE FOR STEP 2 PART TYPE DESCRIPTION QTY

M8X1.25PX20L 4A BOLT

8.4X15.5X6T

4B SPRING WASHER 8.2X15.4X2T

4C FLAT WASHER

2

A B C

A

EN G

LI SH

EN G

LISH

HZ19_T101-5_OM_r1_0_D.indd 10-11 3/21/19 10:19 AM

1312

ASSEMBLY STEP 3 A Open HARDWARE FOR STEP 3.

B Attach LEAD WIRE to bottom end of CONSOLE CABLE. Pull LEAD WIRE through RIGHT CONSOLE MAST (1). After pulling the lead wire through the mast, the top of the CONSOLE CABLE should be located at the top of the mast.

C With the RUNNING DECK in the raised position, attach the RIGHT CONSOLE MAST (1) to the BASE FRAME (2) using 4 BOLTS (A), 4 SPRING WASHERS (B) and 4 FLAT WASHERS (C).

NOTE: Do not tighten bolts completely until after the console is assembled.

ASSEMBLY STEP 4

A Open HARDWARE FOR STEP 4.

B Gently place the CONSOLE (5) on top of the CONSOLE MASTS (1&4). Attach the LEFT SIDE first using 2 BOLTS (A), 2 SPRING WASHERS (B) and 2 FLAT WASHERS (C).

C The CONSOLE CABLES (6) are tucked into the CONSOLE MAST (4). Using the lead wire carefully pull the CONSOLE CABLE (6) out of the CONSOLE MAST (4). Detach and and discard the LEAD WIRE. Connect the CONSOLE CABLES (6) and carefully tuck wires in masts to avoid damage.

D Attach the RIGHT SIDE of the CONSOLE (5) using 2 BOLTS (A), 2 SPRING WASHERS (B) and 2 FLAT WASHERS (C).

E Pull the top of the CONSOLE (5) towards the back of the treadmill and HOLD while TIGHTENING THE LEFT AND RIGHT SIDE BOLTS (A).

NOTE: Be careful not to pinch any wires while assembling the console.

HARDWARE FOR STEP 4 PART TYPE DESCRIPTION QTY

M8X1.25PX15L 4A BOLT

8.4X15.5X1.6T

4B SPRING WASHER 8.2X15.4X2.0T

4C FLAT WASHER

5

A B C

41

4

6

HARDWARE FOR STEP 3 PART TYPE DESCRIPTION QTY

M8X1.25PX20L 4A BOLT

8.4X15.5X6T

4B SPRING WASHER 8.2X15.4X2T

4C FLAT WASHER

A B C

A B C

(STEP E)

A

B

C

1CONSOLE CABLE

2

RUNNING DECK

EN G

LI SH

EN G

LISH

HZ19_T101-5_OM_r1_0_D.indd 12-13 3/21/19 10:19 AM

1514

TREADMILL OPERATION This section explains how to use your treadmills console and programming.

The BASIC OPERATION section in the TREADMILL GUIDE has instructions for the following: LOCATION OF THE TREADMILL

USING THE SAFETY KEY

FOLDING THE TREADMILL

MOVING THE TREADMILL

LEVELING THE TREADMILL

TENSIONING THE RUNNING BELT

CENTERING THE RUNNING BELT

USING THE HEART RATE FUNCTION

ASSEMBLY STEP 5 A Open HARDWARE FOR STEP 5.

B Attach the RIGHT AND LEFT SIDE CONSOLE JOINT COVERS (1) using 8 SCREWS (A & B).

C REMEMBER to tighten ALL BOLTS & SCREWS completely now that assembly is finished.

HARDWARE FOR STEP 5

PART TYPE DESCRIPTION QTY

4X10L 4A SCREW

1

A B

B

4X15L 4B SCREW

A

T101

Running Area: 140 x 51 cm / 55 x 20

Net Weight: 75 kg / 165 lbs.

Dimensions (LWH) : 178 x 85 x 140 cm / 70 x 34 x 55

EN G

LISH EN

G LI

SH

HZ19_T101-5_OM_r1_0_D.indd 14-15 3/21/19 10:19 AM

1716

4 6

810121416 QUICK SPEED KM/H

DIREKTWAHL GESCHWINDIGKEIT KM/H

2

QUICK INCLINE %

DIREKTWAHL STEIGUNG %

CHANGE DISPLAY

ANZEIGENWECHSEL

ENTER EINGABE

START PAUSE

STOP HOLD TO RESET

INCLINE STEIGUNG

SPEED GESCHWINDIGKEIT

TIME ZEIT

CALORIES KALORIEN

PROGRAMS PROGRAMME

INCLINE STEIGUNG

SPEED GESCHWINDIGKEIT

DISTANCE ENTFERNUNG

HEART RATE HERZFREQUENZ

CONSOLE OPERATION Note: There is a thin protective sheet of clear plastic on the overlay of the console that should be removed before use.

A) LED DISPLAY: Incline, Speed, Time, Distance, Calories, Heart Rate

B) WORKOUT QUICK KEYS: press to select your workout.

C) START: press to begin exercising, start your workout, or resume exercising after pause.

D) STOP: press to pause/end your workout. Hold for 3 seconds to reset the console.

E) INCLINE +/- KEYS: used to adjust incline in small increments (0.5% increments).

F) SPEED +/- KEYS: used to adjust speed in small increments (0.1 mph increments).

G) INCLINE QUICK KEYS: used to reach desired incline more quickly.

H) SPEED QUICK KEYS: used to reach desired speed more quickly.

I) CHANGE DISPLAY: press to change display feedback during workout.

J) FAN KEY: press to turn fan on and off.

K) FAN: personal workout fan.

L) SPEAKERS: music plays through speakers when your CD / MP3 player is connected to the console.

M) AUDIO IN JACK: plug your CD / MP3 player into the console using the included audio adaptor cable.

N) AUDIO OUT / HEADPHONE JACK: plug your headphones into this jack to listen to your music through the headphones. Note: when headphones are plugged into the headphone jack the sound will no longer come out through the speakers.

O) USB INPUT: 1A/5V USB output power.

P) WATER BOTTLE POCKETS: holds personal workout equipment.

Q) TABLET/READING RACK: holds tablet or reading material.

R) HEART RATE PULSE GRIPS: used to measure heart rate.

J DR R

BE FI

G

JC

L L

P P

H

K

Q

A N M O

EN G

LI SH

EN G

LISH

HZ19_T101-5_OM_r1_0_D.indd 16-17 3/21/19 10:19 AM

1918

DISPLAY WINDOWS

TIME: Shown as minutes : seconds. View the time remaining or the time elapsed in your workout.

DISTANCE: Shown as miles. Indicates distance traveled or distance remaining during your workout.

SPEED: Shown as MPH. Indicates how fast your walking or running surface is moving.

INCLINE: Shown as percent. Indicates the incline of your walking or running surface.

CALORIES: Total calories burned or calories remaining left to burn during your workout.

HEART RATE: Shown as BPM (beats per minute). Used to monitor your heart rate (displayed when contact is made with both pulse grips).

GETTING STARTED 1) Check to make sure no objects are placed on the belt that will hinder the movement of the treadmill.

2) Plug in the power cord and turn the treadmill ON. (The ON/OFF switch is next to the power cord.)

3) Stand on the side rails of the treadmill.

4) Attach the safety key clip to part of your clothing making sure that it is secure and will not become detached during operation.

5) Insert the safety key into the safety keyhole in the console.

6) You have two options to start your workout:

A) QUICK START UP

Simply press the START key to begin working out. Time, distance, and calories will all count up from zero. OR...

B) SELECT A WORKOUT OR TARGET

1) Select your PROGRAM with the +/- buttons and press ENTER when your desired PROGRAM is displayed.

2) Adjust the SETTING with the +/- buttons and press ENTER when your desired SETTING is displayed.

3) Press START to begin.

EN G

LI SH

EN G

LISH

HZ19_T101-5_OM_r1_0_D.indd 18-19 3/21/19 10:19 AM

2120

3) WEIGHT LOSS: A workout designed specifically to target fat. Promotes weight loss by increasing and decreasing the speed and incline, while keeping you in your fat burning zone. Includes 10 levels.

Speed and Incline changes, segments repeat every 30 seconds.

1) MANUAL: Adjust your speed and incline manually during your workout.

2) INTERVALS: Improves your strength, speed and endurance by increasing and decreasing the speed throughout your workout to involve your heart and other muscles. Includes 10 levels.

Speed changes and segments repeat 90 seconds and 30 seconds.

1) DISTANCE: Push yourself and go further during your workout with 13 distance workouts. Choose from 1 mile, 2 miles, 5k, 5 miles, 10k, 8 miles, 15k, 10 miles, 20k, half marathon, 15 miles, 20 miles and marathon goals. User sets starting speed levels.

2) CALORIES: Set goals for burning calories. Calories burned are calculated using distance and speed.

TARGET PROFILES

WORKOUT PROFILES

Segment Warm Up 1 2 Cool Down Time 4:00 Mins 90 sec 30 sec 4:00 Mins

Level 1 0.5 1.5 2 4 1.5 1 Level 2 0.5 1.5 2 4.5 1.5 1 Level 3 0.5 1.9 2.5 5 1.9 1.3 Level 4 1 1.9 2.5 5.5 1.9 1.3 Level 5 1 2.3 3 6 2.3 1.5 Level 6 1 2.3 3 6.5 2.3 1.5 Level 7 1.4 2.6 3.5 7 2.6 1.8 Level 8 1.4 2.6 3.5 7.5 2.6 1.8 Level 9 1.4 3 4 8 3 2

Level 10 1.4 3 4 8.5 3 2

Segment Warm Up 1 2 Cool Down Time 4:00 Mins 90 sec 30 sec 4:00 Mins

Level 1 0.8 2.4 3.2 6.4 2.4 1.6 Level 2 0.8 2.4 3.2 7.2 2.4 1.6 Level 3 0.8 3.0 4.0 8.0 3.0 2.1 Level 4 1.6 3.0 4.0 8.8 3.0 2.1 Level 5 1.6 3.7 4.8 9.6 3.7 2.4 Level 6 1.6 3.7 4.8 10.4 3.7 2.4 Level 7 2.2 4.2 5.6 11.2 4.2 2.9 Level 8 2.2 4.2 5.6 12.0 4.2 2.9 Level 9 2.2 4.8 6.4 12.8 4.8 3.2

Level 10 2.2 4.8 6.4 13.6 4.8 3.2

( mph ) ( km/h )

Segment Warm Up Each segment is 30 seconds Cool Down

Time 4:00 Mins 1 2 3 4 5 6 7 8 4:00 Mins

Level 1 Incline 0 0.5 1.5 1.5 1 0.5 0.5 0.5 1 1.5 0.5 0 Speed 0.5 1.5 2 2.5 3 3.5 4 3.5 3 2.5 2.3 1.5

Level 2 Incline 0 0.5 1.5 1.5 1 0.5 1 0.5 1 1.5 0.5 0 Speed 0.5 1.9 2.5 3 3.5 4 4.5 4 3.5 3 2.6 1.8

Level 3 Incline 0.5 1 2 2 1.5 1 1 1 1.5 2 1 0.5 Speed 0.5 2.3 3 3.5 4 4.5 5 4.5 4 3.5 3 2

Level 4 Incline 0.5 1 2 2 1.5 1 1 1 1.5 2 1 0.5 Speed 1 2.6 3.5 4 4.5 5 5.5 5 4.5 4 3.4 2.3

Level 5 Incline 1 1.5 2.5 2.5 2 1.5 1.5 1.5 2 2.5 1.5 1 Speed 1 3 4 4.5 5 5.5 6 5.5 5 4.5 3.8 2.5

Level 6 Incline 1 1.5 2.5 2.5 2 1.5 1.5 1.5 2 2.5 1.5 1 Speed 1 3.4 4.5 5 5.5 6 6.5 6 5.5 5 4.1 2.8

Level 7 Incline 1.5 2 3 3 2.5 2 2 2 2.5 3 2 1.5 Speed 1.4 3.8 5 5.5 6 6.5 7 6.5 6 5.5 4.5 3

Level 8 Incline 1.5 2 3 3 2.5 2 2 2 2.5 3 2 1.5 Speed 1.4 4.1 5.5 6 6.5 7 7.5 7 6.5 6 4.9 3.3

Level 9 Incline 2 2.5 3.5 3.5 3 2.5 2.5 2.5 3 3.5 2.5 2 Speed 1.4 4.5 6 6.5 7 7.5 8 7.5 7 6.5 5.3 3.5

Level 10 Incline 2 2.5 3.5 3.5 3 2.5 2.5 2.5 3 3.5 2.5 2 Speed 1.4 4.9 6.5 7 7.5 8 8.5 8 7.5 7 5.6 3.8

Segment Warm Up Each segment is 30 seconds Cool Down

Time 4:00 Mins 1 2 3 4 5 6 7 8 4:00 Mins

Level 1 Incline 0 0.5 1.5 1.5 1 0.5 0.5 0.5 1 1.5 0.5 0 Speed 0.8 2.4 3.2 4.0 4.8 5.6 6.4 5.6 4.8 4.0 3.7 2.4

Level 2 Incline 0 0.5 1.5 1.5 1 0.5 1 0.5 1 1.5 0.5 0 Speed 0.8 3.0 4.0 4.8 5.6 6.4 7.2 6.4 5.6 4.8 4.2 2.9

Level 3 Incline 0.5 1 2 2 1.5 1 1 1 1.5 2 1 0.5 Speed 0.8 3.7 4.8 5.6 6.4 7.2 8.0 7.2 6.4 5.6 4.8 3.2

Level 4 Incline 0.5 1 2 2 1.5 1 1 1 1.5 2 1 0.5 Speed 1.6 4.2 5.6 6.4 7.2 8.0 8.8 8.0 7.2 6.4 5.4 3.7

Level 5 Incline 1 1.5 2.5 2.5 2 1.5 1.5 1.5 2 2.5 1.5 1 Speed 1.6 4.8 6.4 7.2 8.0 8.8 9.6 8.8 8.0 7.2 6.1 4.0

Level 6 Incline 1 1.5 2.5 2.5 2 1.5 1.5 1.5 2 2.5 1.5 1 Speed 1.6 5.4 7.2 8.0 8.8 9.6 10.4 9.6 8.8 8.0 6.6 4.5

Level 7 Incline 1.5 2 3 3 2.5 2 2 2 2.5 3 2 1.5 Speed 2.2 6.1 8.0 8.8 9.6 10.4 11.2 10.4 9.6 8.8 7.2 4.8

Level 8 Incline 1.5 2 3 3 2.5 2 2 2 2.5 3 2 1.5 Speed 2.2 6.6 8.8 9.6 10.4 11.2 12.0 11.2 10.4 9.6 7.8 5.3

Level 9 Incline 2 2.5 3.5 3.5 3 2.5 2.5 2.5 3 3.5 2.5 2 Speed 2.2 7.2 9.6 10.4 11.2 12.0 12.8 12.0 11.2 10.4 8.5 5.6

Level 10 Incline 2 2.5 3.5 3.5 3 2.5 2.5 2.5 3 3.5 2.5 2 Speed 2.2 7.8 10.4 11.2 12.0 12.8 13.6 12.8 12.0 11.2 9.0 6.1

( mph ) ( km/h )

EN G

LI SH

EN G

LISH

HZ19_T101-5_OM_r1_0_D.indd 20-21 3/21/19 10:19 AM

2322

USING YOUR CD / MP3 PLAYER / BLUETOOTH SPEAKERS 1) Connect the included AUDIO ADAPTOR CABLE to the AUDIO IN JACK on the top right of the console and the

headphone jack on your CD / MP3 player.

2) Use your CD / MP3 player buttons to adjust song settings.

3) Remove the AUDIO ADAPTOR CABLE when not in use.

4) If you dont want to use the SPEAKERS, you can plug your headphones into the AUDIO OUT JACK on the right side of the console.

5) To connect to the Bluetooth speakers open your Bluetooth settings, turn on Bluetooth, scan for new devices, look for Horizon T101 and select connect.

APPS CONNECTION Your Horizon machine is APPs ready, allowing you to use Bluetooth technology to wirelessly connect your smart phone or tablet to your treadmill. The APPs can be downloaded from either the iTunes store for IOS devices or from the Google store for Android devices. Available APPs include fitDisplay, Kinomap, Zwift and WeChat (for China market only).

Eng: Waste Disposal VISION Fitness / HORIZON Fitness / TEMPO Fitness / TREO Fitness products are recyclable. At the end if its useful life please dispose of this article correctly and safely (local refuse sites).

Ger: Entsorgungshinweis Die Produkte VISION Fitness/HORIZON Fitness/TEMPO Fitness/TREO Fitness sind recycelbar. Fhren Sie das Gert am Ende der Nutzungsdauer einer sachgerechten Entsorgung zu (rtliche Sammelstelle).

Dut: Verwijderingsaanwijzing VISION Fitness / HORIZON Fitness / TEMPO Fitness / TREO Fitness producten zijn recyclebaar. Breng het apparaat aan het einde van de gebruiksduur naar een in recycling gespecialiseerd bedrijf (plaatselijk verzamelpunt).

Fre: Remarque relative la gestion des dchets Les produits VISION Fitness / HORIZON Fitness / TEMPO Fitness / TREO Fitness sont recyclables. Lorsque cet appareil arrive en fin de vie, veuillez lliminer de manire correcte et en toute scurit en le dposant dans une dchetterie communale.

Ita: Indicazione sullo smaltimento I prodotti VISION Fitness / HORIZON Fitness / TEMPO Fitness / TREO Fitness sono riciclabili. Quando lapparecchio non servir pi, portarlo in un apposito punto di raccolta della propria citt (punti di raccolta comunali).

Spe: Gestin de residuos Los productos de VISION Fitness / HORIZON Fitness / TEMPO Fitness / TREO Fitness son reciclables. Cuando se termine su vida til, por favor deshgase de este artculo de forma correcta y segura en un punto limpio.

Prb: Descarte Os produtos VISION Fitness / HORIZON Fitness / TEMPO Fitness / TREO Fitness so reciclveis. No final de sua vida til, descarte este equipamento corretamente e com segurana (sites de locais de lixo).

ChT: VISION Fitness / HORIZON Fitness / TEMPO Fitness / TREO Fitness ()

ChS: VISION Fitness / HORIZON Fitness / TEMPO Fitness / TREO Fitness

TO RESET THE CONSOLE Hold STOP key for 3 seconds.

FINISHING YOUR WORKOUT When your workout is complete, the unit will beep. Your workout information will stay displayed on the console for 30 seconds and then reset.

EN G

LI SH

EN G

LISH

HZ19_T101-5_OM_r1_0_D.indd 22-23 3/21/19 10:19 AM